In order to find the correct replacement hubs for your EZ Loader boat trailer you will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped…
Hey Rick, sorry to hear about the leaking seals! Looks like the kit you had installed was the part #KOD53FR which for a replacement seal you'd want the part #GS-2250DL and then for bearings #25580 and #02475.
Thanks for reaching out, Nick! I'm not 100% sure what your bolt pattern is so I'll include a few different options. Some of the numbers you gave are OEM number so based off that I THINK your bolt pattern is a 5 on 4-1/2. You will want to…
Hey Carlos, the closest option we have would be the Tandem Axle Jeep Style Trailer Fenders part #HP62VR which is 72 inches long and 10 inches wide. It is also diamond plate like you wanted but it is not painted.
While we do have the best size for your 24x60 cargo carrier #e98874, I recommended using a larger size than the #GC47FR. As a great alternative, I suggest going with the 4' 9" x 5' 3" #GC77FR. This will help make up for the vertical…
I'd go with the part #UF21-001091. It locks the tire of each axle so well to each other that the trailer would not roll at all if pushed while you were hitching up. I attached a review video for more info. If you wanted to be super cautious a…
For your 2002 Jayco Heritage Pop-Up camping trailer, I recommend the Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option - Black #295-000019. This latch fits doors that are 1-1/4 inches to 1-1/2 inches thick and installs into latch…
The Bauer Products Motorhome Door Lock #BA64FR is the closest we have to the cutout size you have. This door lock requires a 5-1/4" wide x 4-1/2" tall opening so you will need to widen your opening by 1/2'. This door does have a…
It's normal for some clearance lights to ground through the mounting screw instead of running an extra wire so there's nothing wrong with that. For the amber clearance lights you can use part #MCL67AB and for the red part #MCL67RB. These both…
If you are looking for the center section of the bracket that is in the picture you submitted of the #MCL67ARB that you referenced the correct part number you need is the #A65P that you referenced.
In order to find a replacement side marker light for your 2015 Dynamax Dynaquest I recommend taking some measurements of the current light. There is not a direct replacement available so you will need to find something that is a close match and…
Toss one over your load to keep rock, mulch, or leaves in place on a utility or dump trailer while the mesh lets air pass so it won't flap around at speed. Pick a size that matches your bed and use your tie-downs or bungee cords at the attachment points for a snug fit. Mesh tarps are great for containment, but they're not for rain coverage, and some grommets may wear if stressed hard.
No, a mesh tarp should not be used as a covering for rain. Mesh is designed for airflow and containment, not to keep water out. If you need weather protection, consider a solid, non-mesh cover. For hauling, mesh works well to keep materials in place without catching as much wind.
Durability varies; some mesh tarps hold up well while others can have grommets or eyelets tear after a handful of uses. Avoid over-tightening a single point and spread tension across more attachment points. Inspect grommets before each trip and consider reinforcing high-stress corners. If a grommet starts to loosen, adjust your tie pattern to reduce strain.
Look at material and weight per square yard. An example spec is 100 percent Polyethylene at 6.5 ounces per square yard. Verify these details in the product specs to match your needs. Heavier-feel mesh can seem sturdier, but also check grommet quality and the number of attachment points for secure tie-downs.
Yes, mesh tarps help keep loads like rock, leaves, mulch, and construction debris from blowing out. The breathable design reduces flapping in the wind compared to solid tarps. Size the tarp to cover the bed with some overlap and secure it to multiple tie-down points. Using bungee cords or similar tie-downs at several spots helps distribute the load and improve hold.
Filters
