Hey Dylan - both M-3 plates measure 81-3/4 inches wide, so you'd need to trim off a little bit. The aluminum one #M348FR would be easier to trim, so I'd pick that over the steel one. The hinge runs the full width so you’ll still get solid…
Hey Craig, yes the Kenda 215/60-8 Bias Trailer Tire with 8" Galvanized Wheel #AM3H325 would be the best wheel and tire in the size you have currently of 215/60-8. It has the highest Load Range and also a galvanized wheel that will work great to…
Hey Marty. Caliber lists the weight capacity for their Edge Glide XL Transition Plates item #CA47EJ as matching your trailer's ramp door. So whatever your ramp door capacity is is what transition plates will sport. The 4-pack has a combined…
Hey Bill, yes you can use the Caliber Edge Glide 2.0 Transition Plate for Enclosed Trailers #CA42TJ on a plywood ramp extension. Do you have snowmobiles?
To replace the hubs on your trailer, I will need you to pull one of your hubs and look for the inner and outer bearing. On the face of each of these bearings, there is a number. That number will help me get you the correct hubs for your trailer. If…
There are large RVs, over 40 foot Winnebagos as an example, that only use up to a 4K generator. It seems like a generator is what you need for the power the items you want to have in the trailer. We currently do not have generators or inverters that…
Hey Alan - you can absolutely use the M3 plate at the door-to-floor gap. Many folks run one on the outside edge and another inside for a totally smooth roll-through. The steel plate #M368FR gives you extra strength if you’re using pallet jacks or…
If you are questioning the quality of the tires or their ability to hold up I recommend just replacing the tires. Defiantly be sure to check the age of the tires to ensure they are not too old. I typically recommend once a tire is 5 years old to go…
Hello David, thanks for reaching out. It is possible to switch your trailer over to a lunette ring/pintle hitch system. Basically you will need to replace your current A-frame coupler with a channel coupler like part #LR76VR. This will allow you to…
The Dexter trailer with 4 inch drop that you referenced #7685269-EB seemingly is the correct axle but you need to verify the hub face to hub face dimension as well. If that dimension is 95 inches this is the correct axle since this has 80 inches…
I'll try to start this answer off with some of the most important information- the batteries. The batteries you will need to power all of this would need to be 12v deep-cycle batteries with enough amp hour rating to power all of the tools and…
As long as the 2-Leaf Slipper Spring w/ Radius End for 1,000-lb Trailer Axles - 24-5/8" Long #e36SR is the same length as your current flat-end spring you can use it as a replacement. The only "radius" style of leaf spring that…
Hey Dylan - both M-3 plates measure 81-3/4 inches wide, so you'd need to trim off a little bit. The aluminum one #M348FR would be easier to trim, so I'd pick that over the steel one. The hinge runs the full width so you’ll still get solid…
Hey Craig, yes the Kenda 215/60-8 Bias Trailer Tire with 8" Galvanized Wheel #AM3H325 would be the best wheel and tire in the size you have currently of 215/60-8. It has the highest Load Range and also a galvanized wheel that will work great to…
Hey Marty. Caliber lists the weight capacity for their Edge Glide XL Transition Plates item #CA47EJ as matching your trailer's ramp door. So whatever your ramp door capacity is is what transition plates will sport. The 4-pack has a combined…
Hey Bill, yes you can use the Caliber Edge Glide 2.0 Transition Plate for Enclosed Trailers #CA42TJ on a plywood ramp extension. Do you have snowmobiles?
To replace the hubs on your trailer, I will need you to pull one of your hubs and look for the inner and outer bearing. On the face of each of these bearings, there is a number. That number will help me get you the correct hubs for your trailer. If…
There are large RVs, over 40 foot Winnebagos as an example, that only use up to a 4K generator. It seems like a generator is what you need for the power the items you want to have in the trailer. We currently do not have generators or inverters that…
Hey Alan - you can absolutely use the M3 plate at the door-to-floor gap. Many folks run one on the outside edge and another inside for a totally smooth roll-through. The steel plate #M368FR gives you extra strength if you’re using pallet jacks or…
If you are questioning the quality of the tires or their ability to hold up I recommend just replacing the tires. Defiantly be sure to check the age of the tires to ensure they are not too old. I typically recommend once a tire is 5 years old to go…
Hello David, thanks for reaching out. It is possible to switch your trailer over to a lunette ring/pintle hitch system. Basically you will need to replace your current A-frame coupler with a channel coupler like part #LR76VR. This will allow you to…
The Dexter trailer with 4 inch drop that you referenced #7685269-EB seemingly is the correct axle but you need to verify the hub face to hub face dimension as well. If that dimension is 95 inches this is the correct axle since this has 80 inches…
I'll try to start this answer off with some of the most important information- the batteries. The batteries you will need to power all of this would need to be 12v deep-cycle batteries with enough amp hour rating to power all of the tools and…
As long as the 2-Leaf Slipper Spring w/ Radius End for 1,000-lb Trailer Axles - 24-5/8" Long #e36SR is the same length as your current flat-end spring you can use it as a replacement. The only "radius" style of leaf spring that…
Enhance Your Snowmobile Trailer with Caliber Parts
Caliber snowmobile trailer parts offer a blend of quality and functionality. With features like trimmable designs and low profiles, they ensure smooth sled gliding and easy installation. Perfect for enthusiasts looking to upgrade their trailer's performance and safety.
Caliber parts enhance trailer performance by providing a smooth glide for sleds, thanks to their low-profile design. They are easy to trim and install, making them adaptable to various trailer setups. This ensures a safer and more efficient loading and unloading experience.
Caliber parts are designed for durability, handling heavy-duty use with ease. They can withstand the weight of heavy items and provide excellent grip, ensuring your trailer remains in top condition even under demanding conditions.
Caliber parts are easy to install due to their trimmable nature, allowing customization around cleats and other obstacles. They come with screws that hold them securely, though additional screws may be needed if parts are trimmed extensively.
Yes, Caliber parts provide excellent traction for snowmobile tracks. They are designed to grip boots and tracks effectively, preventing slipping and ensuring a smooth transition onto the trailer, which is crucial for safety and ease of use.
Caliber parts are highly customizable, making them suitable for various trailer setups. Their trimmable design allows for easy adaptation to different trailer sizes and configurations, ensuring a perfect fit and optimal performance.
Filters
