Snow Plow Parts

Hello Jeremy, Thanks for reaching out. I do have a couple options that could work for what you’re looking to do, though I want to set expectations up front that one option isn’t available in black and the other depends a bit on how your trailer is…

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

You can switch from a 5-Leaf #e74SR to a 7-Leaf #e37SR as long as you are replacing all your leaf springs. Do note the 7-leaf springs are going to be roughly 3/4" taller so you may also need taller U-Bolts like the #MR66ZR which are 7-3/4"…

Slipper spring setups, like parts #e74SR and #APT6SE for 7K axles, do have different hanger sizes so what you'll want to do is cut off the older hangers and do some mock-ups of your new system before installing the hangers. Start off by mocking…

Hey Daniel, Chances are your slipper spring has flattened out over time and is longer than it originally was. Typically an older trailer that may not have had its suspension replaced anytime recently is around an inch longer than it was originally.…

We do have a shoe for a Meyer snowplow with a 3/4" diameter shaft, the Replacement Shoe Assembly for Meyer Snowplow - Standard (Drive Pro) #3371303002. I have added a link to a video review with dimensions of this part for you to check out as…

Hey Joe, thanks for the information! To replace your Dexter 072-079-01 leaf springs, I recommend the 7-Leaf Double-Eye Spring for 8,000-lb Trailer Axles item #EM28AJ. This is a 4,000 lbs leaf spring designed for 8,000 lbs axles. It's got 7-leafs…

The parts are different and cannot be interchanged; an angled cylinder simply angles the blade, while the lift cylinder like #3371304203 you mentioned will raise it vertically. The part you mentioned is for a Western Hydraulic snow plow, and for an…

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

Hey Bill, so yeah we worded the fit of the lock you mentioned odd but it's not going to fit a 3 inch setup but we can help as we have the Blaylock EZ part #BLTL-60-40D that was designed for 3 inch diameter setups like you have.

2,500 PSI is the max pressure rating of the Replacement Lift Cylinder part #3371304201.

Hey, Chris! I checked in with Curt and they let me know that they just recently came out with a new harness, part #C28DQ. I just got it added on our website. This is a custom harness so you be able to plug it in, ground it, and then run a power wire…

Hello Jeremy, Thanks for reaching out. I do have a couple options that could work for what you’re looking to do, though I want to set expectations up front that one option isn’t available in black and the other depends a bit on how your trailer is…

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

You can switch from a 5-Leaf #e74SR to a 7-Leaf #e37SR as long as you are replacing all your leaf springs. Do note the 7-leaf springs are going to be roughly 3/4" taller so you may also need taller U-Bolts like the #MR66ZR which are 7-3/4"…

Slipper spring setups, like parts #e74SR and #APT6SE for 7K axles, do have different hanger sizes so what you'll want to do is cut off the older hangers and do some mock-ups of your new system before installing the hangers. Start off by mocking…

Hey Daniel, Chances are your slipper spring has flattened out over time and is longer than it originally was. Typically an older trailer that may not have had its suspension replaced anytime recently is around an inch longer than it was originally.…

We do have a shoe for a Meyer snowplow with a 3/4" diameter shaft, the Replacement Shoe Assembly for Meyer Snowplow - Standard (Drive Pro) #3371303002. I have added a link to a video review with dimensions of this part for you to check out as…

Hey Joe, thanks for the information! To replace your Dexter 072-079-01 leaf springs, I recommend the 7-Leaf Double-Eye Spring for 8,000-lb Trailer Axles item #EM28AJ. This is a 4,000 lbs leaf spring designed for 8,000 lbs axles. It's got 7-leafs…

The parts are different and cannot be interchanged; an angled cylinder simply angles the blade, while the lift cylinder like #3371304203 you mentioned will raise it vertically. The part you mentioned is for a Western Hydraulic snow plow, and for an…

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

Hey Bill, so yeah we worded the fit of the lock you mentioned odd but it's not going to fit a 3 inch setup but we can help as we have the Blaylock EZ part #BLTL-60-40D that was designed for 3 inch diameter setups like you have.

2,500 PSI is the max pressure rating of the Replacement Lift Cylinder part #3371304201.

Hey, Chris! I checked in with Curt and they let me know that they just recently came out with a new harness, part #C28DQ. I just got it added on our website. This is a custom harness so you be able to plug it in, ground it, and then run a power wire…