Thanks for asking Glen, I found the specs you were asking about. Bigfoot Hydraulic Tongue Jack #BF34FR has 16.5 inches of lift, and when it’s fully extended it measures at 24 and a half inches overall. Retracted, it sits at 8 inches, so you get a…
Hey Bill. We've got just over a dozen options for 15" steel wheels that'll work with the Kodiak Disc Brake Kit item #K2R35S, you were looking at. I have linked our selection below. The 15" x 6" Rim Dexstar Steel Mini Mod…
Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…
Hey Josh, so we can help but we don't have any custom fit gooseneck hitches that fit your 1976 Ford F-250. Best option would be a universal style option like the Curt plate part #C65500 which would need to get welded to the top of the truck frame…
Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…
Hey John, the replacement gear kit you'd need is the part #TJD-12000-RODNUT which I attached two pictures that have instructions and an install diagram.
The Thule Wingbar Evo crossbars like #TH711320 have channels on top of them that standard roof rack accessories that are designed for channel mounts. The track nut part #853-5715 that you referenced would fit in this top channel as well.
I would be happy to help! Since your 2021 Subaru Outback Touring XT has the factory 4-way connector I recommend using the 7-way Connector Kit #ETBC7L which is designed specifically for wireless trailer brake controllers. This 7-way plugs into your…
Dexter recommends that you check the wires of the brake assemblies of your trailer to determine which magnet would be what you would need. If the wires are white you would need part #BP01-265 and if they are yellow part #BP01-301. However, aside from…
No, they're not the same. The BP01-301 fits 12-1/4" x 4" Dexter brake assemblies and the BP01-330 DEXTER fits newer Dexter brake assemblies made after 2017 that are 12-1/4" x 5". We are out of the BP01-301 as well and have…
The correct bearing kit for a Dexter 4,400 lbs axle is item #BK2-100. The Dexter 4,400 lbs axles use the same bearings and seals as a Lippert 3,500 lbs axles. This kit includes inner bearing item #L68149, inner race item #L68111, outer bearing item…
Sized for spots that accept a 1/4 inch diameter, these padlocks work well for securing 5th wheel hitches in puck systems, pin box stabilizers, couplers, and propane tank brackets. If your setup needs at least 2" of usable shackle space, this size is a match; if the opening is smaller (like some bike rack hook holes), a 3/16 inch diameter may be required. Measure the lock hole to confirm a clean fit.
Yes, if the head or base has a 3/8" hole that a 1/4" shackle can pass through. Verify the hole size on your setup and ensure the shackle has enough usable length to clear the latch area. Remove any safety pin first so the shackle can seat fully.
Not for some racks; 1/4" can be too large for certain frame-hook lock holes. Measure the padlock hole—if it's around 1/4", it may be tight; a 3/16" shackle can fit where 1/4" will not. If the rack you're using accepts 1/4", a 1/4" shackle can work well. Confirm the hole size before buying.
They've been used on wider couplers, pin box stabilizers, 5th-wheel hitches, and to secure propane tanks on a truck camper. Some platform bike racks also accept them when the lock point fits 1/4". Measure your lock points, as some racks need 3/16" instead. Keyed-alike options can let one key open multiple locks and the compact size carries easily.
Yes, a 1/4" diameter shackle with at least 2" of usable space can lock a Companion-style 5th-wheel in puck systems, and locking a single puck keeps it secured. Check that the puck handle's lock point accepts a 1/4" shackle and has enough clearance for the shackle length. Make sure the shackle can pass fully through the lock point without binding.
Filters
