Hey Don, thanks for reaching out! I recommend using the etrailer E-Track Backing Plates w/ Hardware #e66RR to secure the etrailer Horizontal E Track #e25VR to your hardwood floor. If you were going to be putting the bolts through the floor and into…
Hi Richard; we have no way of knowing what mounting bracket/brakes are on your Load Rite trailer. If you have Dexter/Tie Down Engineering disc brakes with a 9.6" rotor there is a good chance the #DX89UR will fit. However, it is probably best to…
Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…
The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…
The Aries Oval Nerf Bars #AA32ZD you're looking at are confirmed to fit your 2019 Ram 1500 Classic with the Quad Cab. This is the cab with the full front doors and the smaller rear doors. If you have the full doors at the front and the back then…
I attached a picture I got from Pace that covers exactly what the maintenance looks like for the Pace Switchblade tonneau covers like part #311-SWFA06A29 that you asked about.
Hey Jack, the Furrion Chill HE RV unit like the part #FR52PR is going to be your best solution. It is the quietest and draws the lowest amount of power at 11.2 amps compared to most similar options that are around 15. We've tested all of the…
The closest axle we have to what you need is the part #20440I-EZ-60 which has very similar specs as what you need, but the spring center is off by one inch as it is 48 inches on this axle. The overall capacity is 2,000 lbs and the hub face to hub…
The Draw-Tite Front Mount Trailer Hitch Receiver #65080 is designed to fit the Toyota Tundra starting with the 2007 model. It is likely that the door for oil filter access you're referencing on your 2021 was added later or is present in certain…
The front mount trailer hitch options for a 2019 Toyota Tundra, the Curt Front Mount Trailer Hitch Receiver part #31198 or Draw-Tite Front Mount Trailer Hitch Receiver part #65080 will both work of TRD models. That said, you will either need to cut a…
The phone operator was very helpful and made my purchase easy. I will keep this website handy.
Harold
Gillsville, GA
Bimini Top Parts with external end
External end fittings cap your bimini pole and connect to a hinge with a pin for a snug, dependable link. Options include 1/4" flange thickness and a 1/4" pin hole, so you can match the hardware you already have. Stainless steel choices offer a heavy-duty feel. Measure your pin size and flange thickness to get the clean, perfect fit you're after.
Yes, heavy duty stainless steel External Ends are available and noted as great quality. Choose this material if you want a robust feel and clean look. Check the finish and fit on your frame and verify the pin and tab dimensions before installing.
Match the External End to your bimini pole diameter and to your jaw slide and deck hinge style. Confirm the eye end hole and your hinge pin are the same size, like 1/4". If you move to 1/4" flanges from 3/16", update the related pieces so everything lines up.
An External End tab can have a 1/4" hole that fits a 1/4" pin. Measure your hinge pin and verify the eye end's hole diameter matches. Also check tab dimensions; an example tab measures 1-1/4" long x 1" wide x 1/4" thick to gauge compatibility.
External Ends are commonly 1/4" thick at the flange/tab. If you're replacing 3/16", the parts available here are 1/4". Consider switching all related flanges to 1/4" if the smaller flange raised strength concerns. Measure your existing tab to confirm before ordering.
Filters
