# 1
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I love it. This rack works great. Bikes ride stable and secure on the back of my vehicle and travel trailer as I can switch it back and forth depending on what I'm doing.
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
# 2
Swagman Upright Bike Rack for 1 Bike - Roof Rack Crossbars - Frame Mount
Planning on bringing bikes while camping. I mounted 2 of the Swagman bike racks to my new Sportrack on my pop-up camper. The bikes fit perfectly. The racks seem sturdy enough. Not heavy duty, but for my needs they should be fine. Assembly was relatively fast and easy.
We have used the Swagman Roof Rack a number of times when we have needed the additional bike carrying capacity. It took a couple attempts to get the initial spacing of the bike rack properly balanced on the van’s roof rack as recommended by the instructions. But it was easy to do and once set was very easy and quick to put on and take off. The rack works great, the bike is easy to put into place and secure. The bike and rack are very stable and quiet and haven’t required any mid-trip adjustments. We always put the cheapest bike on the roof (lol) but do use a bit of duct tape to protect the finish just Incase. We are very satisfied with the rack and consider it quite a deal for the money.
# 3
RockyMounts MonoRail Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
At age 75, I have purchased many bike racks over the years…..this one has no equal in loading and unloading…
This rack is really, good. The only thing i add to make it better is small strap that holds the front wheel to the front wheel bracket. I never had a problem with it, but i like to make sure it is secure. It is a solid bike rack and worth every penny. I would buy this over the Kuat version any day.
# 4
Swagman Titan Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Tilting
One of the few racks that will clear my Jeep's large rear mounted spare tire without using an extender. The other is the Allen which doesn't have the nice features the Swagman Titan has. Tips enough to allow partial opening of Jeep rear door, but enough to open the soft top rear window. The vertical portion of rack tips slightly toward vehicle (at least it does on mine). Would be better if the horizontal "S" shaped piece could be turned around to dip down, moving it further from the spare tire, but there are only holes drilled to mount it as shown. Can't attest to the durability yet, but it doesn't wobble even a tiny bit. Have to compliment everyone I spoke with at etrailer. very nice and extremely helpful.
eTrailer.com had my new Swagman Titan bike rack delivered super fast. I received the right amout of email communication informing me of the status of my order, plus I could track my delivery directly from the eTrailer website. Awesome! As for the hitch, I am so happy with it. I was tired of taking the front wheel off my bike and cramming it into the back of my small Corolla, it never really fit right, was always a struggle, and then I had no room for anything else in my car. Now, I just hang my bike onto the rack and strap it in, takes less than 60 seconds and I have all the extra room in my car and don't have to fold down the back seats. The other feature I really like is that this bike rack has an integrated locking cable, once your bike is on the rack, you attach the locking cable so now your bike is locked onto the rack. Someone can't take your bike off the rack and walk away with it when you aren't looking. I also got the Swagman bike rack locking pin, that attaches the bike rack to the car hitch. I've used the bike rack twice so far and it makes my life so much easier. Solidly built bike rack that is well worth it. Thank you eTrailer, you rock!
# 5
Hollywood Racks SR1 2-Bike Carrier - Spare Tire Mount
This HRSR1 bike carrier will not fit a 2023 Jeep Wrangler JL UNLESS you remove the stock Liddy Light and associated bracket. Upon discovering this, I was able to locate an aftermarket kit which allows for the relocation of the light to just above the rear camera. The kit was easily installed and the bike mount was installed just as easily as the directions explain. The new location of the light is partially obscured with the bikes mounted and, although not ideal, it is adequate and certainly better than total removal. I was unable to find any mention of this situation in the install instructions or reviews prior to purchase of the rack. I just wish I had been aware of this before purchase. I would have rated 5 stars for this product were it not for the slight hiccup. Kudos to etrailer. It is always a pleasure to do business with them. They are very helpful, friendly and knowledgeable.
JeepIt's sturdy even off-road, and it's simple to take on and off. I've had to use my spare tire twice since owning this rack, and although I have to remove my bike and loosen the bike rack bolts a bit, it comes off and goes back on with minimal effort, which is nice when you're on the Alaska Highway and it's snowing. I've carried my full-suspension bike on this rack for 35k miles all over the U.S. and Canada. I like how my bike fits close to the tire, where I lock it. My tailgate opens without the bike touching the side of my Jeep. Great bang for the buck.
# 6
Curt Clamp-On Bike Rack for 3 Bikes - 2" Ball Mounts
Arrival was timely. Instructions were slightly confusing at first but once understood, installation was pretty easy. And the bike rack is working fine.
This is the best product online. I had to do a few adjustments to make room for the clamp on the trailer hitch. The particular ball hitch I had had a reinforcement welded to the ball which I had to have a piece taken off. Once it was filed down the clamp worked like a champ. Now I have a $200 bike rack that I purchased a year ago that is obsolete. The product arrived early and in good shape. I would definitely buy this bike rack and use this company again!
# 7
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
I bought this bike rack back in April but wanted to make sure I used it to give the best review. First I want to say I did a lot of research on bike racks and found this one to be the best one to fit my needs. The best price I found was on etrailer.com, at the time it was When I called the customer service to place my order, I spoke to Dan. He was very pleasant on the phone and took the time and listened to what I needed and understood my concerns. I ordered the bike rack and also ordered the Thule Snug Tite Hitch Lock and Anti-Rattle Device and the Thule Cable Lock w/ One Key System Lock. Dan suggested I also get the Thule Bike Adapter Bar, which I never even thought of getting. Delivery was in about two business days, which was really fast and at the time of order they were running a special free delivery over $99. When I went to put it together I noticed I was missing the flat cap screw M6 x 16mm, part number #853-5787-02. I emailed Dan and within 24 hours received an email that the part was sent out and also in the email their was a link to track the order. After I received the part I did notice that the flat cap screw was actually in the 2 inch adaptor sleeve. The instructions were very easy to read, and it took me about 20 minutes to put together. I did have an issue when I positioned the stinger into the cradle, with the 8mm locking nut, it was not staying tight and when I took it off I noticed the threads inside were gone, so I ended up going out to Lowes and buying a new one and its holds perfectly fine. I also had a question about that part because it is not a locking part and was worried someone would try to steal the rack. I contacted etrailer.com to find if they make a locking device for this and they said no but I can contact Thule to double check, I'm still waiting for an answer back from Thule. The weather finally broke and we installed the rack onto my hitch, tightened it and it doesn't rattle. When I finally used the rack and put my bike on, it did sway a little but at 50 mph I was very happy with it. The trailer comes out just enough away from my car that I do not have to fold completely out and I can open my trunk with no issues. I am very happy with my purchase and had a great customer experience with Dan. Would highly recommend ordering from them to anyone.
# 8
Saris Bones EX 3 Bike Rack - Trunk Mount - Adjustable Arms
This bike rack is perfect for our Kia carnival minivan. Very sturdy and does not put pressure on the back of the van.
Great product so far! Easy to install and adjust. A little tricky to load 2 large handlebar mountain bikes and a third smaller bike, but we just turned them sideways with the front wheels taken off. We had racks on bikes which were probably the impediment. We got them on though! Love how it folds up easy for quick storage. Works great on 2014 Subaru Outback.
# 9
Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount
The BEST bike carrier by far!! We are both in our 7th decade and even I alone (5’2” 120 lbs) can manage to attach this in my hitch without any issues. It’s so easy to load both our hybrid and e-bike and they are super secure. We love that it folds up small and wheels away when not in use. This bike carrier is worth every penny!!
This rack is perfect! eTrailer had it shipped and at my home in almost no time. I drove with it on the car today, and it was solid and secure. It's super easy to get on and off the hitch. I'm 5'1 and I was able to load the bike on with the ramp without a struggle. Thanks for the thorough video and comparison information. It made this purchase easy.
# 10
Thule T2 Pro XTR Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Great product, great company to do business with. etrailer is the best. Friendly, helpful and they made sure the bike rack was shipped immediately and it was delivered on time.
The quality of the rack is very sturdy and well built. I needed a rack that has a 12” spacing between wheels do to the baskets on each bike, and this rack delivered that. The issues I have with this rack are: I have a GMC Yukon suv and with the rack mounted I have to lift my two Lecritc 2.0 e-bikes, at 60 pounds each up over 24” to get it mounted. It sure could use ramps, which I know it did not come with. The clamp hold down does not work with fenders on a bike. It does not clamp very well on the cross bar (male and female) type do to the width and the angle of the cross bars. When clamping in front of the front fender makes the bike very unstable, and will require additional strapping and tie downs to secure the bikes. It claims it is for e-bikes, but only if it has no fenders. Nice rack, just not for me.
# 11
Curt 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Frame Mount - Tilting
I installed this rack onto a Curt trailer hitch which is mounted onto a 2017 Honda Fit. I have been using it intermittently for several months, probably about 5 times with one bike and twice with two bikes. I give some pros and cons below and then elaborate. Pros: easy to assemble, easy to mount and dismount bikes, easy to lock and unlock, how to put the rack into different positions is intuitive Cons: inconvenient to put the rack into different positions, inconvenient to mount the rack onto the hitch, rack protrudes about 15 inches from bumper when in flipped up position (seems very vulnerable to someone backing into it in a parking lot, very inelegant looking I say the repositioning is intuitive because there is really only one way you could possibly place the pins for each position. But removing and replacing two pins is much less convenient than turning a knob or a lever, like some racks do. Also many racks fold and flip in such a way as to look very unobtrusive when in non-use mode. This one looks like kind of a monstrosity. That does not really bother me but it might bother some owners. The part that does bother me is how far it protrudes from the car. I back into parking spaces whenever possible to avoid someone bumping into the rack and damaging it (which happened to a friend). My number one suggestion for Curt is related to mounting the rack onto the hitch. Make it easier to tell when the holes are lined up so that the bolt/pin will fit and thread. As it is now, if you insert the rack as far as it can go it is way too far in. Ideally, it would be exactly lined up. Failing that, maybe some kind of click or other feedback to know at least that you are in the neighborhood. It would also be great to have an attaching device that is easier to fasten and unfasten than is the bolt/pin. Tip for mounting the rack onto the hitch: I assumed that it would be awkward to hold, what is it 46 pounds?, while trying to line up the rack probe with the receiver. If you have a garage with exposed collar ties, my solution could work well for you. I looped a cargo strap over a collar tie. Then I hooked both hooks of a bungie onto that loop. The idea is that you hook one of the bike frame holders of the rack onto the bungie, suspending the rack a few inches off the garage floor. This takes most of the weight of the rack so that you can just pull up or down and forward until you line up with the receiver. Tip for mounting bikes. Don't put the little screw into the post that prevents you from completely removing the bike frame holders. Remove both holders. Position the first bike, slide the holder into place, position the second bike, slide the holder into place. I found this makes it much easier, because you avoid parts of the bike hitting the holder as you are trying to get the wheels into place. The trick is that if you are mounting only one bike, don't forget to put the second holder back on - or maybe just stick it inside the car right away.
I had a 1 1/4" hitch installed on my 2016 toyota camry (the only size offered on the camry). I was very pleased with the ride. I expected to hear alot of noise like experienced when towing a trailer, but I heard almost nothing accept when going over speed bumps. I had to extend the tire supports to their widest position because having mountain bikes with a step through angled bar, they were more secure the closer i could get the upper and lower support arms to the seat post. The bikes were mounted in opposite directions and only stuck out maybe 6 inches or so. One locking barrel on the lower support arm was malfunctioning and gave me trouble but i called etrailer and they sent a replacement as soon as they were in stock. It comes with a anti rattle hitch pin but I highly recommend purchasing an anti rattle hitch pin with a lock on the end instead of just a clip for more security when unattended. After a few times mounting the bikes and figuring out the best way they should be positioned (pedals positions, direction of bike, and that my wife's smaller bike fit better going on first with my larger bike on the outside) I can mount the rack and bikes and be ready to go in just 5 minutes. (70 pounds on a torque wrench recommended for the hitch pin) I am overall pleased with my purchase i would recommend this product.
# 12
Saris SuperClamp EX Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Wheel Mount
At the age of 70, I needed a “friendlier” mounting and bike access rack. A platform rack seemed to be the solution. I had one caveat. My Subaru Forester had a 1and 1/4” receiver (with a non-standard 3/4” length mounting hole). My Volvo had a tuck away 2” receiver. After some research I gravitated toward Thule only to find out they had no solution for my above conundrum. In fact their customer service offered no interest in solving my problem which others also must have had. More research…enter Saris! An American made company with an innovative solution. I quickly received my SuperClamp EX-2 from ETrailer along with excellent customer service support. The ease of constructing the unit for use and the obvious structural integrity was immediately apparent. My wife couldn’t believe how easy it was to use and to stow away on my garage wall after use. Thank you Saris and ETrailer for a wonderful product and experience. I guess American made is still alive and well. I highly recommend this product and the associated companies.
Purchased this bike rack last year and am very pleased with the stability of the rack. The straps and clamps secure the bike well to the rack. Some things that I learned: When attaching the rack onto your hitch, it helps to put a piece of tape on the rack (hitchtite) once you have lined up the holes. This will make it easier to find the exact location of the holes the next time that you want to use the rack. Finding the exact location allows you to smoothly hand tighten the bolt to the end of the hitch. At that point, just use a socket wrench to finish the tightening. When putting the bike on the rack, I loosely secure the clamps to the tires at first. This allows me to rotate the tires to find the right location in the wheel well for the straps to go around the spokes. I next secure the bike with the straps and then fininsh securing the clamps to the tires.
# 13
Hollywood Racks Destination Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
Used it twice so far, it meets my expectations based on other reviews. It's easy to load the bikes (8 minutes or so for 4 bikes) and to move up or down. Glad I bought this "lighter" platform rack rather than the swagman because while it's not hard to get into the hitch, neither is it "light". Anything heavier would definitely be a pain. Hopefully straps etc are durable over the long haul. No problem getting 2 adult and 2 kids bikes on. Glad I went with a platform rack over a bar. My sister has the bar rack and says it's impossible to get 4 bikes on.
Ok so I I was going to buy a safari rack which ended up being about $100 more once you tacked on taxes and shipping from another website. This was on sale and had really good reviews. I bought this and have used it long enough to leave an honest review. It’s a really good rack, quality built, and If anything should break on the rack etrailer has all the replacement parts for very cheap prices. I have used this racks for shuttle duties and held 4 big enduros bikes several times. You don’t need to use the extra red straps sent with the rack for the bikes to be very secure. As someone stated before in the reviews long wheelbase bikes like size L or XL frame enduro or DH bikes might only be able to strap one wheel and frame attachment (the one wheel will be too long to get a good strap on), but all you need to do is drill a hole and move the clamp outboard about 2” and you’ll be good as gold. This rack is awesome and was a heck of a deal. Would recommend and buy again if I ever needed 2 racks? Also not to mention (not that I really care), but the rack was packaged really nice and didn’t come all damaged from shipping, it was really nicely formed foam that was glued in place and not just some hack job some guy tossed in a box. 10/10 !
# 14
Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This bike rack works great for our 2 Lectric 2.0 e-bikes. We mount it on our 2019 Honda Ridgeline. It folds up nicely when it’s on the truck and we are using our bikes. The locking mechanisms work well also. I contacted support for a smaller hook arm to clamp B over the bike frame. They knew exactly what I needed and shipped it - no problem.
I've been using this bike rack alongside a trailer hitch I got here for my small car (chevy bolt ev) and it was exactly what I was looking to get to haul around my fat tire mountain bike bike. Sometimes I throw two bikes on there (either an e-bike, slightly heavier at 60 lbs, or a 2nd mountain bike) and it's perfect.
# 15
Yakima HoldUp Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Works well for transporting two 29" wheeled mountain bikes. However, after one year it's starting to rust in several areas (see attached photos), and the front wheel arms are becoming increasingly difficult to raise and lower. Finally the locking cable is extremely rusty as you can see in the attached photo. I'm not sure how durable this rack will be long term.
We have had this bike rack for one year and use it every week-end. My wife has a Trek e-bike (52 lbs) and I have a regular Trek hybrid (23 lbs). The rack is very sturdy and I have no issues driving at highway speeds, there is no movement of the bikes. Very easy to load and unload.
# 16
Kuat NV 2.0 Base Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Matte Black
I've taken this rack all over New England on the front of my Dodge Ram 3500 pick up truck with a truck camper. I had no idea it was possible to love a bike rack so much. After one drive I didn't ever worry about it again. So nice that it locks up when I am camping or taking a quick stop for food on the road. So glad I bought it from etrailer. They totally help me pick the perfect rack for my challenging set up.
Still very new, but what an awesome bike rack! Assembly was a snap and the rack is rock-solid when you secure it to the hitch receiver. etrailer was amazing too - excellent communication, price and fast, free delivery. Overall I am extremely happy with the rack and service!
# 17
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 18
Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
etrailer: prompt delivery, fair price! Rack: It does fit my (2) Gazelle T10 eBikes. 1) I found I had to adjust every setting to get bikes to fit. Until you learn there are many adjustments, it does not seem like the center/vertical clamps will reach both seat posts. 2) The ramp is barely usable; my wheels are max it will fit and you must have at least 12ft of clearance on each side of car to get bike lined up with ramp. 3) My bikes have a "walk" feature, this is not usable as its too awkward to hold the walk button down and move around the rack. I found its easier to abandon the ramp and load front then rear wheel. I will rig up a wheel stop, on ends of each wheel holder so bike will not roll off while I strap it in. 4) Rack did NOT come with a lock for hitch pin; this is very disappointing as they say in manual this is an optional item. Every rack I have seen at least has a clip that would otherwise hold the hitch pin in if somehow the bolt loosened up. 5) The rack weight is the lightest I have found. 6) You must load the first bike (closest to car) from car passenger side. This will avoid you bike pedals hitting the vertical bar. That means you must load the 2nd bike manually as there is no way to get the pedals past the vertical bar. I will get used to this, I hope. 7) The rack is a few inches above the receiver (part that goes into hitch) so if you have a low hitch this might be an issue with ground clearance. With both bikes mounted up, it seems very stable and hopefully will be secure in travel.
This is a great product and works beautifully! The only issue was some sloppily made plastic turn knobs that were cross threaded on arrival. However, Yakima immediately shipped out replacements. It carries two large E bikes easily. They fasten solidly and are easy to load and unload!
# 19
Saris Bones EX 2 Bike Rack - Adjustable Arms - Trunk Mount
Best bike rack for my Mitsubishi Outlander. Bikes are secure and it’s easy to use.
So far, so good. The confirmed fitting for my car was excellent as described by etrailer. The test will be an upcoming 3 hour road trip.
# 20
Saris Guardian 2 Bike Rack - Fixed Arms - Trunk Mount
I think there should have been more study done before telling me your rack could be used on a 2017 Kia Sedona LX minivan.
5 Stars for ease of ordering , free shipping and ease of fitting bike rack to my car
What our customers are saying:
"Everyone that bought before me was right! I got my rack in time for my next days off and putting it together was fast too. And I'm a grandma!! Thank you for being fast and honest! You beat anyone in my town hands down!"