# 1
Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2
Great directions for manual assembly, quality metal and parts. Solid and exactly the heavy duty I was looking for to use with my slide in truck camper.
The Brophy jacks were strong, stable, easy to position, and easy to lift and lower my camper. it is a much better method than having four jacks to maneuver. And it cut down my time to 30 minutes total to load my camper instead of an hour and a half! I have to start from my garage and winch my camper down on a cart to the street face because of the incline driveway is so dramatic and my camper won’t fit in my garage if it is attached to the truck. I couldn’t be more happy they were great and now I have my truck loaded with my very modern camper and I’m enjoying quite the holiday! I’m using the 3 ton 67 inch trophy jacks and I’m lifting an 800 pound gross camper. The stability is outstanding.
# 2
Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 1
Gave it a three due to the modifications that had to be done to make it fit. I had to grind down the outside of the pad about 3/16" to make the stabilizer fit up into the bumper of our Scamp. In addition, I shimmed the top down about 5/32 so it would lock into place without forcing it. One stabilizer had epoxy which looks very sloppy. This on the edge where it should be spot welded - hope this is the case! Fortunately, I'd read reviews indicating that this was not a direct replacement for Scamp 13'ers. Folks should be aware they may have to do some work since the stabilizers may not fit out of the box. Once modified, they work as expected.
I drilled two 3/8" holes in the top of the rail and used two stainless bolts to hold it on. Works very well for this application. It folds and holds the trailer for loading, and if I have to leave it somewhere, and don't want the tongue sitting on the ground. I used it on a Harbor Freight 4x4 trailer I am building to pull with my Can-Am Spyder. Love it!!!
# 3
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 24" Lift - 3,500 lbs - White
Jack works very well. Not fast but gets the job done. Unfortunately I can't lower my tailgate fully without hitting the jack. Tried to rotate the head as I saw some jacks allowed. This one won't allow that. Very satisfied otherwise. Used less than one full season so can't offer an opinion on durability.
Mounted quick and easy. Plenty of wire for electrical hook up. Lots of power even with a full load of water in the front tank. The only change I made to installation was longer bolts to accept washers and nuts to the bottom side of hitch. I didn't trust the taped holes in the thin hitch frame. This was no fault of the new jack. Still working strong. A back saver that's worth the money. I should have bought one years ago!
# 4
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
Perfect replacement, works great, excellent shipping time and service. Just wish I had got the electric motor that goes with the legs.
Ordered this from etrailer instead of other sites as I knew the shipping would be faster. Sure enough I got the item in 4 days on Thursday and Installed it on Sunday. Very quick and easy. Took longer to get all my tools and set up items together than the actual work. The item was a exact fit with installation being feeding the legs through the holes in the floor down from the inside and installing the 4 clamping bolts to hold them in, the gear box on the lead leg and the cross bar and motor. Now it purrs like a kitten when activated instead of clanking and creaking and blowing fuses. Actual install time was probably 1.5 hours taking my time and injecting extra grease into the gears and lead screw. These replacement units have a grease fitting for both which is great and should allow them to last forever! Being a safety freak I used a 3 ton jack with a 4X6 placed long ways to catch the I beams under the trailer then placed 3 ton car jacks under the frame also and for extra safety backed my truck bed under the tongue for extra security while I worked. The price was crazy great, the fit was excellent and the shipping was fast as usual. less money in parts and 2 hours of work probably easily saved me a grand over taking it to a RV repair shop! Thanks etrailer. Saved me again!
# 5
Ultra-Fab Ultra Scissor Jacks - 24" Lift - 13,000 lbs - Qty 2
Definitely a heavier duty version of our campers stock stabilizers. They bolted right up to the brackets and glad we have new stabilizers. I hope the paint lasts on these as that seems to be an issue with the other, cheaper stabilizers. Time will tell.
if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.
# 6
Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - QTY 2
Quality product w/ quick delivery
work very well for portable leveling couldn't fix too Jayco Melbourne any where under RV. Still trying to figure a spot.
# 7
Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1
Jacks Appear to be exactly as advertised. Delivery was early. I bought this pair of jacks to replace a J-2500 that came on my Kodiak Cub. The J-2500 bent when I over torqued it while jack was not extended far enough. I found out this 5000 pound model is not a drop in replacement. I had to drill additional mounting hole in the jack to match existing holes in trailer frame.
They went on a custom made trailer build that’s not yet in service. Seem to function as advertised.
# 8
Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs
This is the second one of these we've owned. Works real good, a bit of over kill. The thing could probably lift the whole trailer.
It installed very easy. For a 2500lbs jack, it seems a little light weight. It does lift the trailer but seems kinda wobbly because the post size is so small. Other than that it works as advertised. Thank you for getting it to me so fast.
# 9
Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 5,000 lbs - Qty 2
Jacks Appear to be exactly as advertised. Delivery was early. I bought this pair of jacks to replace a J-2500 that came on my Kodiak Cub. The J-2500 bent when I over torqued it while jack was not extended far enough. I found out this 5000 pound model is not a drop in replacement. I had to drill additional mounting hole in the jack to match existing holes in trailer frame.
Initial reaction is that this is a great, high-quality product. Only took me 1-1/2 hours to install two (both on the door-side) that had been damaged. Would've been even faster but I needed to modify the bracket that bolts onto the frame for the rear stabilizer. BTW, the two stabilizers had to be replaced because, as a first-time trailer owner, the dealership never told me to NEVER USE YOUR STABILIZERS TO LEVEL YOUR TRAILER! I hope to save at least one other person the hassle and expense of having to replace your stabilizers because you didn't know any better--I know now and will never forget! At least the new stabilizers are higher quality and really weren't difficult to switch out.
# 10
Leveling Scissor Jack - 24" Lift - 5,000 lbs
Much better jack than the one that came with the tow trailer. This 70 year old woman had no difficulties installing it. One year later still works great!
leveling jack was delivered very promptly and in good shape. installed on my 5th wheel easily and works fine. a bit lighter duty than the OEM jack but darn good value for the price and will get the job done. etrailer is the best!
# 11
Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
Easy to install both in under an hour. Provide good stability to small (boat) trailer when deployed. I can see the paint/powder will be as durable as they were as simple to install
Bought these for my cargo trailer. Did not get around to installing them for several months. When I finally unpacked them, the “foot” of one came off while I was unwrapping them. I had to drill holes and add a few screws to reattach. There was no damage to the box. They still serve their purpose, just disappointing.
# 12
Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs
The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.
I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."
# 13
Ultra-Fab Stackable Stabilizers for Small Trailers and Campers - 6,000 lbs - Qty 2
Perfect for the four corner supports of our Jayco 175 RD. Much easier to deal with than the scissor jacks installed on the camper. E trailer got them to us quickly as usual!
Our camper came with stabilizers only in the back. Once we level it we put these under the front corners and it gets rid of any movement in the camper like you get when front is only on tongue jack.
# 14
Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System - 10,000 lbs
One small part was missing from my Ground Control TT. Carol Korren expedited delivery of the missing part and the UPS truck pulled up at the moment I needed the part. Fantastic customer service!
We love our one touch jack system. We used in on a 3 month camping trip out west setting up probably 40 plus times and we continue to use our camper and the jacks work great!
# 15
Lippert High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift
Box is damaged and tape all over with clear tape holding box closed and first thought is missing parts and paper work and instructions to install ! Pictures taken and open up box finding all parts inside except for the paper work instructions to install, also the rubber cover for the water poof motor is damaged also!
Good thing stabilizer was easy to install because there were no directions included. Item was delivered quickly. I received item within a week.
# 16
Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift
Easy to install and functioned perfectly. Customer has been utilizing it for a year and still raves about it. Thank you
Pros: Works better than I anticipated. Looks great and has better ground clearance than the stock scissor-jack stabilizers. Cons: Installation instructions/documentation weak or non-existent. If all of the instructions, wiring diagrams and documentation were in one place on the web page under a separate tab rather than having to dig through the reviews and the Q & A’s, I would have given this a 5 star rating. I ordered the LCI Power Stabilizer Jacks with the white switch Kit (LC369774) because I wanted the switches mounted in the camper wall so they would be better protected than if they were mounted in the flimsy fender skirts of my camper. I also needed the bolt-on spacer kit (LC673594) for both the front and rear jacks to clear a propane line that runs along the length of the frame. Installation was relatively easy, although there are NO instructions on how to install the spacers kits; the video on etrailer.com was no help whatsoever with the installation. I bolted the jack mount brackets to the shorter side of the spacers using carriage bolts and flange nuts; the slotted holes in the spacers accepted the carriage bolts, aligned perfectly with the holes in the jack mounts, and allowed me to install them without having to try to fit a wrench inside. Then it was just a matter of drilling holes in the frame at the appropriate spacing for flange bolts/nuts through the slotted holes on the end of spacers. I was very pleased with how the switches and the switch compartments looked once installed. Again, though, it took lots of digging to find the wiring diagram and then the matrix for the switch wire colors, because the wires on the white switch are colored differently than the black switch that all of the diagrams show. Also, it states on the jack installation instruction sheet that the power must be a minimum of 10 gauge wire (AWG-10), but nowhere on the wiring diagram does it say anything about that. AWG-10 is a MUST because of the way current drops over a distance. In the case of my camper, it is a 30 foot run which requires that gauge of wire for 20 AMPs.
# 17
Stallion Stabilizer Jacks - 7" Drop Leg Travel - 22-1/4" - Qty 2
I mounted this Stabilizers Jacks to the back of a 4x8 utility trailer. I use the trailer to haul my Honda ATV to MotoAmerica motorcycle races. Once the ATV is removed I lower the jacks and mount my tent inside the trailer. These stabilizers allow me to safely move around in the tent without fear of the trailer tipping.
Jacks worked great. Added them to an aluminum 2 place enclosed snowmobile trailer that did NOT like humans to walk up the rear ramp when unhooked and empty!? ...problem solved.
# 18
Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black
As always a big help in getting what I need, and wanted. Good tec help, fast service. Already installed.
The bolt pattern matched my trailer so it was very easy. No skill needed. I soldered a connection on and hooked it directly into the battery. I had to drill a hole for my foot extension. So far so good. 23 foot travel trailer.
# 19
Electric Trailer Jack - Drop Leg - A-Frame - 22-1/2" Lift - 3,500 lbs
The CargoBuckle G3 ratchet tie-down straps and 45 degree mounting brackets worked great. Makes loading and unloading a breeze.
This jack was the perfect solution for my application. I have a new enclosed trailer that came with a manual crank and only a tiny battery to run the lights. I did not want the expense of having to buy and cable up a larger battery to just support the tongue jack. Took me 5 minutes to install this new jack using the three bolts that were already on my OEM jack. Now I just back up my truck, plug in the 7-way, and I'm able to move the tongue up and down as needed. Great!
# 20
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.
It looks like a great product am anxious to install them. I have a symbol of them in my garage and I have one with a really crooked foot. The bolt hole on the retracting arm was drilled in the wrong place so it is totally crooked, not a deal breaker though. I’m sure the are more than Adequate
What our customers are saying:
"I received this order yesterday. Thanks for the outstanding service. I appreciate it! Thanks, Alex"