Code: HA81760-HA81783-HBC
Trailer Brake Controller Specs:
Features:
Power output and braking aggressiveness can be easily adjusted with built-in buttons on this time-delayed brake controller. Includes digital display and manual override. Activates brakes with a preset intensity.
Installation Notes:
You will also need item 37185 ($55.30) to complete your wiring.
The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.
More Information >Code: HA81760-HA81783-HBC
Trailer Brake Controller Specs:
Features:
Power output and braking aggressiveness can be easily adjusted with built-in buttons on this time-delayed brake controller. Includes digital display and manual override. Activates brakes with a preset intensity.
Installation Notes:
The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.
More Information >Trailer Brake Controller Specs:
Features:
Power output and braking aggressiveness can be easily adjusted with built-in buttons on this time-delayed brake controller. Includes digital display and manual override. Activates brakes with a preset intensity.
Installation Notes:
Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.
If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.
Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.
More Information >Trailer Brake Controller Specs:
Features:
Power output and braking aggressiveness can be easily adjusted with built-in buttons on this time-delayed brake controller. Includes digital display and manual override. Activates brakes with a preset intensity.
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Videos
for Trailer Brake Controller
Help Articles
for Trailer Brake Controller
Expert Answers
for Trailer Brake Controller
While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I&…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
view full answer...The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...The number you provided,…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...Filter Products (8)
Contact and Help
What our customers are saying:
Outstanding service. Thanks for the painfree ordering of product.
John
Collierville, TN