See what our Experts say about this Bulldog Winch Accessories and Parts

• How to Choose Winch Capacity and Parts Needed for Quick Connect Winch Wiring
  Long story short, that's not going to work for you even with a double line pull using a snatch block like the # CU881079. In reality, you need at least 1.5x the GVWR of your vehicle when it comes to winch capacity. The # BDW10044 I mentioned as a better choice would be the bare minimum you'd be able to get away with and still be able to recover your 2019 Nissan Frontier from a situation that required a winch. The 6000-lb capacity ComeUp # CU854768 is not going to work with your 4700-lb...
  view full answer...
• Can The 7-Way Trailer Connection Be Used To Power Winch If Vehicle Is Running
  The wiring that feeds the 12-volt accessory circuit on the 7-way trailer connector is of too small a gauge to allow enough power to pass through to run a winch. The main function of that circuit would be for lighter-duty applications, such as providing power for interior trailer lights or to maintain a trailer mounted battery. The Bulldog Winch Trailer Winch - Wire Rope - Roller Fairlead - 4,400 lbs, # BDW15019, will require some power as it draws 28 amps at 0 lbs but 340 amps at full...
  view full answer...
• Wiring for Electric Winch at the Front and Rear of a 2015 Chevy Silverado 3500 Duramax
  First, you are going to need a couple sets of quick disconnects such as # BDW20133. You will need enough 2 to 4 gauge wire to reach from the front of the truck to the batteries and from the rear of the truck to the batteries. Another option is to get a couple of winch wiring kits, # BDW20207. The winch power and ground wires will attach to one disconnect and the wiring to the batteries will attach to the mating quick disconnect. Diesel trucks normally have 2 batteries so the isolator...
  view full answer...
  
• How To Add Quick Disconnect Harness for Electric Boat Winch
  I may have a solution for you, but there's not going to be a wiring harness that can be used that will provide you with the power you're going to need to pull from the battery to power the winch. Your best bet might be to create some sort of quick disconnect for each of the batteries that you can either hook up when needed, or leave attached to the vehicles. This would require cutting off the battery clamp ends of your winch and putting quick disconnects like the Dutton-Lainson Electrical...
  view full answer...
• How to Wire Two Electric Winches to a Vehicle with Dual Batteries
  When wiring two separate winches to a vehicle with dual batteries, you will need a circuit breaker for each winch. A circuit breaker is designed to protect the vehicles circuitry in the event of a short in the winch wiring. Almost all winch circuit breakers are equipped with an auto-resetting feature. If the winch you have did not come with a circuit breaker or you simply need to replace the circuit breaker, you will want to use one rated for the maximum amperage draw of the winch. If...
  view full answer...
• Recommended Quick Connects for a Winch Being Installed on a Boat
  Since the quick connects are only rated to 50 amps I'd beef up your cables to cover your 150 amp max pull rating. The 6 AWG is a minimum so you can go bigger, luckily. I'd steer towards something like the Bulldog Winch Rear Wiring Kit # BDW20207 or for just the quick connects # BDW20133. This kit/connectors are going to work with 2 AWG wire which is larger, however they are rated for up to 175 Amps so you'll have your coverage.
  view full answer...
• How Long is the Wire on the 12K Bulldog Winch and Wiring Needed to Connect to Vehicle Battery
  The battery cable on the Bulldog Winch Trailer Winch # BDW10039 is 6' long. Since you are wanting to run this off of the vehicle battery you will need larger gauge wire but but only from the vehicle battery to a quick disconnect like the Bulldog Winch Quick-Connect Set # BDW20133. You would then need enough 2 gauge wire to reach from your vehicle battery to the rear of your vehicle. We have the Bulldog Winch Rear Wiring Kit # BDW20207 which comes with the quick disconnects, wiring, and...
  view full answer...
• How to Make 20 foot Long 2 Gauge Quick Disconnects for Winch
  I have a solution for you, but there isn't a 20 foot long version of the part # BDW20219 that you referenced. Instead you would need to provide 20 feet of 2 gauge wire and then use the # BDW20133 for quick connects on either end. These connectors are the same as what comes with the 24 foot # BDW20207.
  view full answer...
• Recommended Winch for Front of 2004 Toyota Tacoma 4x4 with Draw-Tite Front Hitch
  The Draw-Tite Front Mount Trailer Hitch Receiver # 65041 is rated for up to 9,000 lbs line pull but you can honestly use whatever size winch you want to for your 2004 Toyota Tacoma. As long as you don't exceed the weight rating of the front mount hitch/winch you are good to go. For your application the 9,500 lb Bulldog Winch Standard Series Off-Road Winch # BDW10042 is a great option because it is rated slightly higher than your front mount hitch (so you get the most out of that weight...
  view full answer...
  
• Quick Connects for Power a Trailer Winch from a Vehicle Battery
  There are some quick connect options for winches. We have # BDW20133 for 2 gauge wire, # BDW20047 for 6 gauge wire. We also have # DL24085 for 6 to 16 gauge wire and # DL24086 that accepts up to 10 gauge wire. I have included a link to our FAQ article on wiring an electric winch that should be helpful.
  view full answer...
• Using Two Different Winches on the Same Winch Wiring Harness
  It sounds to me like you have the Trailer and Vehicle Electric Winch Wiring Kit part # BDW20207 already installed on your Chevrolet Tahoe that is currently ran to a Superwinch S4000. If you are looking to attach the Superwinch Winch 2 Go 4000 SR part # SW1140232 to this wiring harness kit, you can either use the pigtail the runs to the Superwinch S4000 or you can simply cut the clamps off the Winch 2 Go and attach a new set of quick connectors like the Superwinch Quick Connects part # BDW20047...
  view full answer...
• Which Winch Mount And Winch For a GMC Sierra 1500
  To install a winch on your GMC Sierra 1500 I recommend installing a front mount trailer hitch receiver and use a removeable winch mount. This will allow you to have the winch when needed, but also allow you to easily remove the winch when you do not need it. If you can tell me what Year your GMC Sierra 1500 is I would be happy to recommend a front mount trailer hitch receiver for you. I recommend the Bulldog Winch Standard Series Off-Road Winch # BDW10042 which has a 9500lb maximum rating,...
  view full answer...
• How to Wire my Fulton Powered Winch on my Trailer
  For a straight connection your can use the Deka Wire Crimp Connector part # DW05354 and double over your 10 gauge wire to make the crimp hold for you. We often do this when joining two sizes together. If it will be connected outside the trailer use heat shrink like the Deka Primary Wire Heat Shrinkable Tubing part # DW05402. If by Quick Connect your mean the Bulldog Winch Quick-Connect Set w/Dust Cover part # BDW20133 type these would work for you.
  view full answer...
• Why Does the Bulldog Winch Rear Wiring Kit Ground To the Battery and Not the Frame
  In regards to the Bulldog Winch Rear Wiring Kit part # BDW20207, the length of ground wire is included to ensure a good ground on every application. The kits are not tailor made to any one particular application and not all customers will have a good spot to ground the winch x amount of feet away from the rear bumper. The connection to the battery takes this out of the equation and ensures you don't have intermittent function issues caused by a poor ground. If you want to ground the wire...
  view full answer...
• Best Connector for Heavy Duty Winch Cable
  Yes the Bulldog Winch Quick-Connect Set w/Dust Cover part # BDW20133 would be an excellent way to connect your winch to your battery and will allow you to disconnect it when not in use.
  view full answer...
• Recommended Wiring Kit for Hitch Mounted Winch
  The Deka 2 Gauge Professional Service Booster Cables, # DW00161, can be used to power your hitch mounted winch, but it wasn't really designed for that use and I think there is a better option. I recommend the easy disconnect system # BDW20133, that gives you better contacts on both ends than a clamp will allow. The easy connect, disconnect feature allows you a much more convenient option. I have attached an installation video for you of a similar setup.
  view full answer...
• Quick Disconnects for Superwinch Tiger Shark 9.5K Winch # SW1595201
  Electric winches over 9K such as # SW1595201 tend to use 2 gauge wire. For this particular winch I recommend wiring kit # BDW20207 which comes with quick disconnects and the wiring. If the winch is going to be at the front of a vehicle I recommend # BDW20205. And for quick disconnects by themselves you can use # BDW20133.
  view full answer...
• Can 2 AWG Be Used on the Superwinch Winch 2 Go 4000
  The Superwinch Winch 2 Go 4000 comes with 6 AWG. Therefore the correct quick-disconnect terminal would be part # BDW20047 which is rated for 6-10 AWG, not part # BDW20133 which is rated for 2-4 AWG. In order to use the quick-disconnect terminal rated for 2-4 AWG, you would also need to change out the wires in the box that run from the ring terminals on the winch to the quick-disconnect terminal on the back of the box.
  view full answer...
• How to Tell if Bulldog Winch Quick Connect Will Work With Badlands Winch
  There are many different capacities of Badlands winch so it's not possible to tell you outright if the Bulldog Winch Quick-Connect Set for Powersports w/ Dust Cover - 6 AWG # BDW20047 will work with your Badlands winch. You can pretty easily tell though, as if your winch uses the same 6 AWG you can absolutely use the Bulldog Winch Quick-Connect Set # BDW20047.
  view full answer...
• Will Superwinch 2-4 Gauge Wire Quick Connects # SW2236 Work on 12000-lb Winch
  The Bulldog Winch Quick-Connect Set # BDW20133 that you referenced will work with winches that have 2 gauge wiring. The weight capacity of your winch is a function of both motor capacity/wiring gauge, and also its gear train. If your winch uses 2 gauge wiring then you can use this connector # BDW20133. We also offer part # BDW20047 that's designed for use with 6 gauge wiring.
  view full answer...
• 2 Gauge Wiring Quick Connects For Trailer Mounted Winch Running To Vehicle Bumper
  We have the Bulldog Winch Quick-Connect Set # BDW20133. These 2 pole connectors attach to 2 gauge wire and are rated for up to 175 amps of power. It includes a cover with a tether to keep out dirt and moisture when you are not using the connector. We do have these connectors also in the Rear Wiring Kit # BDW20207 which includes 24' of 2 gauge wires. The connections are already attached to the wire making it much easier to install on your truck.
  view full answer...
• How many Quick Connectors are Included in the Dutton-Lainson Electrical Quick Connects # DL24085
  When ordering the Dutton-Lainson Electrical Quick Connect, # DL24805, you will get 2 plastic connectors, one male and one female and 4 quick connect terminals, properly sized for soldering 6 gauge wire into them, to make one complete quick disconnect setup. If you are using a larger gauge wire for installation of a large winch, you would need to go with the Superwinch Quick Connects, # BDW20133, for 2-4 AWG Wire.
  view full answer...
• What is the Amp Rating on the Bulldog Winch Quick Connects
  The Bulldog Quick Connect, # BDW20133, is designed to use 2 gauge heavy duty wire and is used on many of heavy duty winches that have a higher amp draw. The amp draw on some of the winches that recommend the # BDW20133 quick connect is rated for 175 amps. I believe this quick connect will work for you on your plow.
  view full answer...
• Installation And Operation Of Front Mounted Winch On 2010 Chevrolet Silverado 2500
  It does not matter which battery the Superwinch Tiger Shark series winch you mentioned is connected to in your 2010 Chevrolet Silverado 2500 Diesel. The batteries are run in series so you have better cracking amps, but which battery you connect to won't affect any accessories. I suggest runing the engine while using the winch because the alternator will help give you more power and it will keep your batteries from draining and preventing start-up. For the front receiver, I recommend...
  view full answer...

Do you have a question about this Accessories and Part?