Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to be taking a look at part number BDW-20154. This is the Bulldog Hitch Mount Storage Bracket. The receiver mount storage anchor can be mounted in the bed of your truck or in a location that's out of the way. You could also use this in your garage or storage area as a storage mount for a two-inch by two-inch hitch mount accessory. Now this is designed to store the receiver mount in winch assembly when they are not being used. The receiver opening on this unit is going to measure two-inches by two-inches, it's going to feature a pinhole diameter of five-eighth's of an inch. It's made from a nice steel construction, it's got a nice, solid, smooth weld here at the base.
It's going to come with all the hardware that you need to get the mount installed. It's a really simple process- the shank of your receiver is going to slide into the two-inch by two-inch opening. You're going to slide it in to this receiver, and so you get the pinholes to line up with one another and then you'll insert a five-eighth inch hitch pin and clip or hitch lock. Now those items are sold separately but you can find them right here on our website. I want to take some time just to go over the basic measurements of this unit. Starting with the overall length here at the base, that's going to give us a measurement of eight and five-eighths of an inch.
The width of the base, that's going to give us a measurement of six and one quarter, and then the thickness of that base is going to measure a quarter of an inch. Now, the overall height, when I did a measurement, I measured it right at four and one-eighth of an inch. Again, the receiver opening is going to be two-inches by two-inches. The receiver length is going to give us a six-inch measurement. And then when I took a measurement of the height from the top of the base to the center of the receiver cube, I got a measurement of two and three-quarters of an inch, so the height that we have from the bottom of the base, or from the table top, to the center of that receiver would measure about three inches. I'll go ahead and give you the distance that we have from the mount holes.
You can see that it's going to have a mount-in location on each corner. They are situated differently, so this one and this one runs the same direction and then this one and this one runs the same direction as well. So center-on-center, taking a measurement between our mount holes, going this way it looks to be six and one-quarter of an inch and then going this direction, center-on-center, looks to be right at four inches. That's going to do it for our review of part number BDW-20154. This is the Bulldog Hitch Mount Storage Bracket with the two-inch by two-inch receiver. .
Average Customer Rating: 4.7 out of 5 stars (10 Customer Reviews)
Awesome product. We mounted it to our flat deck trailer and it works perfectly for our winch. This Bulldog winch hitch mount is solid and I highly recommend it. Five Stars
I found this product was just the ticket to anchor to my concrete floors in my 4-bay garage. I attach a 12 volt wench to each one to pull disabled vehicles into each garage bay as needed. Works great!
this item worked for what I needed to use for
Just what I need for the temporary use of my Winch on the trailer.
I actually haven’t got to use any of the Bulldog winch receiver brackets as of yet (I ordered 3 total). My plans are to anchor (to the garage concrete floor with 1/2” Red Head anchor bolts) each bracket/receiver to 3 different garage bays. I have a 5,000 lb winch mounted on 2” x 2” recveiver tubing to attach to each Bulldog bracket for winching non running cars into each garage bay.
Shipping was unusual. First bracket came doubled boxed, was in great shape, all hardware was there. Second bracket was single boxed, beat up a bit, but was not damaged and hardware was still in box. Third bracket was singled boxed, beat all to heck, and all hardware was missing (had a big hole in the shipping box). Contacted ETRAILER about shipment, they said they would send out hardware ASAP.
Box delivered last night. . .wow!! that is service. . .Thanks
Great item, fast shipping!!
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
George E.
4/24/2020
working out perfect just what needed to mount in my shop to the concrete to use as pulling system for cars and minor bodyframe work