Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"

Ask the Experts about this Draw-Tite Trailer Hitch

• Hitch Recommended for 2019 Mercedes-Benz Sprinter 25000 Cargo Van
  On this particular vehicle, the design of the rear bumper and its relation to the frame will dictate where the hitch sits. All the hitches available for the 2019 Sprinter 2500 with the standard bumper will sit pretty much up against the underside of the rear bumper as shown in the provided photo. Of the two hitches available for the way your van is set up, either the Curt # C13388 or the Draw-Tite # 75549 would work perfectly. Both hitches have similar weight capacities, but Curt has...
  view full answer...
• Trailer Hitch for 2019 Mercedes Benz Sprinter 2500 with Best Ground Clearance
  If your 2019 Mercedes-Benz Sprinter 2500 has a standard bumper without the step, the Draw-Tite # 75549 is going to provide you with the most ground clearance at 15" from the bottom of the receiver tube to the ground. If your Sprinter has the factory step bumper, you can use the Draw-Tite # 75601, which has roughly 14-3/4" from the bottom of the receiver to the ground. None of the hitches for the 2019 MB Sprinter 2500 will fit on Sprinter vans with a 30-3/8" frame width measured outside...
  view full answer...
• Will Draw-Tite Trailer Hitch # 75549 Fit 2019 Mercedes Sprinter 2500 with 144" Wheelbase
  As long as your 2019 Mercedes Sprinter 2500 features the standard factory bumper the Draw-Tite Max-Frame Trailer Hitch Receiver # 75549 that you referenced will fit perfectly. It will line up to existing holes in the Sprinter's frame rails for a no-drill installation and its robust construction allows for a 6,000 pound towing weight capacity and a 600 pound tongue weight limit. If your Sprinter happens to have the factory step bumper instead then the correct Draw-Tite Trailer Hitch...
  view full answer...
• Trailer Hitch, Wiring, and Brake Controller Recommendation for 2016 Mercedes Sprinter 2500
  Yes, for your 2016 Mercedes Benz Sprinter 2500 the Draw Tite hitch part # 75549 is a fit and my recommendation for your application as it has the capacity you need and installs easily as well. I attached an install video for this for you to check out as well. To install a 7-way all you need is the # TK22115 and then the easiest solution for a brake controller is the Curt Echo Mobile part # C51180 which basically just plugs into an active 7-way and once synced to your smart phone is ready...
  view full answer...
• Trailer Hitch Fit for 2016 Mercedes-Benz Sprinter 2500 Passenger Van With Factory Step Bumper
  There is a trailer hitch that will fit your 2016 Mercedes-Benz Sprinter 2500 passenger van with a factory step bumper, so long as it does NOT have a 30-3/8" frame, measured outside to outside of frame. The correct hitch, which fits either 170 inch wheelbases or 144 inch wheelbases is: - Draw-Tite Trailer Hitch Receiver # 75601 I do want to mention that just from the picture you sent in, it does not look like you have the step bumper, it looks like you may have the standard bumper....
  view full answer...
• Draw Tite Trailer That Fits 2017 Mercedes Benz Sprinter 2500 with 39.5 inch Frame
  Yes, the Draw Tite hitch part # 75549 does fit your 2017 Mercedes Sprinter 2500 passenger van without the rear step and the frame width 39-1/2 inches that you mentioned.
  view full answer...
• Recommended Hitch and Hitch Mounted Step for 2019 Mercedes-Benz Sprinter 2500
  As long as your Sprinter doesn't have the 30-3/8 inch frame width (measured outside frame to outside frame) the Draw-Tite Class III hitch you'd looked at, part # 75549 would be a fit. For a large and very durable hitch mounted step, I'd highly recommend something like the Carr Mega Step, part # CARR190011 for silver or # CARR190011B for black. The step has a whopping 500 lb weight capacity, can can fold up when it's not needed. I'd also highly recommend a hitch lock like # e98882 to prevent...
  view full answer...
• Do Trailer Hitches Install Inside Trailer Frame for 2019 Mercedes-Benz Sprinter 2500
  Both the Draw-Tite # 75549 and Curt # C13388 trailer hitches mount to the inside of the frame so they won't be a problem for your 2019 Mercedes-Benz Sprinter 2500 with the standard bumper. I kind of like the look of the Curt better to I recommend going that route over the Draw-Tite, plus we have found that the Curt hitches tend to have better welds and a thicker powder coat so they are a little more durable.
  view full answer...
• Recommended Wiring and Brake Controller for a 2019 Mercedes-Benz Sprinter 3500
  Glad to hear you've been getting some good use out of your Draw-Tite Max-Frame Trailer Hitch Receiver # 75549! I recommend using a brake controller with the least invasive installation for the intricate OEM wiring on your 2019 Mercedes-Benz Sprinter 3500. For that you need the Tekonsha T-One # 118649 (which tees in behind the tail lights and draws power from the battery) for basic trailer light functions. This then allows you to install the 7-Way Upgrade kit # ETBC7L which gives you...
  view full answer...
• Can Draw-Tite Trailer Hitch # 75549 be Used as a Step on a 2017 Mercedes Sprinter 2500
  The receiver on Draw-Tite trailer hitch # 75549 does stick out past the bumper a few inches on the 2017 Mercedes Sprinter 2500. Take a look at the picture I have included for an example. There isn't a whole lot of space and no grip on the metal receiver so I recommend a hitch step such as # BBS-1102 or, if you will be towing, the Tow & Go Hitch Step for Ball Mounts # RP7060200 as much safer alternatives. I have linked videos on all 3 products for you.
  view full answer...
• Trailer Hitch for 2019 Sprinter 2500, 144"WB, and Std. Bumper
  Yes, the Draw-Tite # 75549 hitch you referenced will fit your 2019 Mercedes-Benz Sprinter 2500 with 144" wheelbase, standard rear bumper, and frame measuring 39-1/4" outside dimension. This installation will not require you to drill any holes and will not interfere with your spare. If you will be towing you need a tow ball and ball mount. Without knowing the offset between the trailer and tow vehicle I can't recommend a specific item, but, I have supplied a link to an FAQ below regarding...
  view full answer...
• 2019 Mercedes-Benz Sprinter 2500 Trailer Hitch Recommendation
  For your 2019 Mercedes-Benz Sprinter 2500 you really can't go wrong with either Curt or Draw-Tite as they are both very respected brands. When choosing which one, you do want to check and see if your Sprinter has the standard bumper or the factory step bumper. If yours has the standard bumper I would go with the Draw-Tite Max-Frame Trailer Hitch part # 75549 because it is a little bit easier to install. It has a GTW of 6,000 pounds and a MTW of 600 pounds which are both the same as...
  view full answer...
• Parts Needed to Equip 2017 Mercedes-Benz Sprinter 2500 with 7-Way and Trailer Brake Controller
  We have 2-inch Class III trailer hitches for your 2017 Sprinter 2500 that you can view on the linked page. Their fits depend on the van wheelbase and bumper style. You can use the drop-down Select Vehicle Style menu tool to choose your specific configuration. Please note that Sprinter frames that measure 30-3/8-inches between the outsides of the frame rails have no confirmed hitch options. Towing capacities vary slightly among the hitches available; for a van without the factory step...
  view full answer...
• Trailer Hitch for 2016 Mercedes Sprinter 2500 Passenger Van w/ 144 Inch Wheelbase & Standard Bumper
  We do have the right trailer hitch receiver that fits your 2016 Mercedes-Benz Sprinter 2500 passenger van with a 144 inch wheelbase and standard bumper, from Draw-Tite. The correct hitch is the Draw-Tite Trailer Hitch Receiver # 75549. Then, if you plan on doing some towing with your van and need a wiring harness the one that fits and is the most reliable is the T-One Vehicle Wiring Harness # 118649.
  view full answer...
• Ground Clearance with Draw-Tite Trailer Hitch Installed on a 2014 Mercedes Sprinter 2500
  We haven't installed Draw-Tite trailer hitch # 75549 on a 2014 Sprinter 2500 but on the 2016 model year after the hitch was installed, see video, it measured 17-1/4 inches from the ground to the top of the receiver opening. So from the ground to the bottom of the receiver would be about 15 inches.
  view full answer...
• Recommended Trailer Hitch Receiver For A 2015 Mercedes-Benz Sprinter
  I have the perfect trailer hitch receiver that is a confirmed fit for your 2015 Mercedes-Benz Sprinter. For this, I recommend using the Draw-Tite Class III Max Frame Receiver Hitch part # 75549 for cab and chassis models and part # 75601 for both the 2500 and 3500 models. I have attached an installation video of this hitch on a 2016 Mercedes-Benz Sprinter Van for you. The Draw-Tite Class III Max Frame Receiver for cab and chassis models has a maximum weight capacity of 600 lbs. tongue...
  view full answer...
• Trailer Hitch for a 2014 Mercedes Sprinter 3500 with 144 Inch Wheelbase and Factory Step Bumper
  For your 2014 Mercedes Sprinter 3500 with 144 inch wheelbase and factory step bumper you will use hitch # 75601. But to be sure you can measure the width of the frame. Frame width is measured from the outside of one frame rail to the outside of the other. If your measurement is 30-3/8 inches then this hitch will NOT fit your van.
  view full answer...
• Trailer Hitch Fit for 2007 Dodge Sprinter 3500 Dually with 170 inch Wheelbase and Standard Bumper
  I have a hitch for you, but the Draw-Tite Class III Max Frame Receiver Hitch # 75549 that you referenced is not confirmed to fit your 2007 Dodge Sprinter 3500 Van, 170 Inch Wheelbase with Standard Bumper. The # 75549 will not fit dually models of the Sprinter. Since the outside to outside frame width of your van is 39-1/4 inch, the trailer hitch you will want for your Sprinter van is the Curt Class III Receiver Hitch # C13388. This hitch offers a 600 pound tongue weight and 6,000 pound...
  view full answer...
• Trailer Hitch & Wiring for 2016 Mercedes-Benz Sprinter 2500 Without Step Bumper
  We do have 2-inch Class III trailer hitch fits for your 2016 Mercedes-Benz Sprinter 2500 so long as its frame does NOT measure 30-3/8-inches from outside edge to outside edge. You can measure the outside width of your van's frame to be sure. Draw-Tite hitch # 75549 will fit your van without step bumper (and if it is not a dually) and will bolt on without drilling. This hitch fits both 144-inch and 170-inch wheelbase models. The written instructions and a helpful article are linked for...
  view full answer...
• Will Trailer Hitch Fit a 2019 Mercedes Benz 170 WheelBase Sprinter Crew Van
  As long as your 2019 Mercedes-Benz Sprinter 2500 doesn't have the 30-3/8" frame (measured outside to outside) then you can use part # 75549 if you have the standard bumper. I have attached an installation video of this trailer hitch on a 2016 MB Sprinter 3500 that you can reference. If you let me know what you plan on using the trailer hitch for I can make additional recommendations as necessary.
  view full answer...
• Towing Capacity Rating for Flat Towing Versus Trailer Towing with 2018 Mercedes-Benz Sprinter 2500
  If your 2018 Mercedes-Benz towing capacity is 5,000 lbs, then the most weight you can flat tow is that 5,000 lbs maximum. The rating for weight distribution systems will not be valid for flat towing a vehicle. You may want to check your owners manual and driver's door jamb to help with towing capacities as some vehicles are rated higher at up to 7,500 lbs and you may simply need to upgrade your trailer hitch. For instance we have many hitches rated for 6,000 lbs towing without...
  view full answer...
• Draw Tite Hitch Fit Recommendation for 2016 Mercedes Sprinter 3500 with 144 inch Wheelbase
  I believe you meant to type 366.5 cm wheelbase as that would equal 144 inches which the Draw Tite hitch part # 75549 would be a fit for your 2016 Mercedes Sprinter if you didn't have the factory step bumper. If you did have the factory step bumper you would want the part # 75601.
  view full answer...
• Does Weight Distribution System Increase Towing Capacity For 2016 Mercedes-Benz Sprinter
  When towing with your Sprinter, you will not be able to tow a trailer that weighs more than the lowest rated component, either your Sprinter or the trailer hitch you install on the Sprinter. With that being said, if you install a trailer hitch like part # 75549 it has a 600-lb tongue weight capacity and a towing weight capacity of 6,000-lbs. If you use a weight distribution system with the # 75549 hitch it does increase the tongue weight capacity to 750 lbs and the towing weight capacity...
  view full answer...
• Weight Distribution for 2016 Mercedes Sprinter Towing 6,000 lb Trailer
  If you are sure an OEM hitch has a 7,500 lb towing capacity without weight distribution that would be the highest rated option as none of the options we have are near that capacity. For a weight distribution system for the range you mentioned the # RP66083 would work well as it has a tongue weight range of 400-800 lbs and features best sway control at preventing sway before it starts. For a 2 inch ball you would want part # A-90 and for a 2-5/16 inch ball # 19286.
  view full answer...
• Does Draw Tite Hitch # 75549 Fit 2019 Freightliner Sprinter with Standard Bumper
  Since your 2019 Freightliner Sprinter has the standard bumper the Draw Tite hitch part # 75549 that you referenced is the correct fit. It also will not interfere with your rear spare either.
  view full answer...
• Hitch for 2012 MB Sprinter 3500 with 170 Extended Wheelbase
  The Draw-Tite Max-Frame Trailer Hitch Receiver # 75549 fits a 2012 Mercedes-Benz Sprinter 3500 with the 170" wheelbase (and standard bumper) and as long as it does not have the 30-3/8" frame, measured outside to outside of frame. If you have the factory step bumper then you need the Draw-Tite Max-Frame Trailer Hitch Receiver # 75601 instead which has the same criteria for fitment. If you're looking to tow with the Sprinter then you need the T-One Wiring Kit # 118650 and a ball mount...
  view full answer...
• Trailer Hitch Recommendation for 2019 Mercedes Sprinter 2500 that Has Fast Install
  For your 2019 Mercedes Sprinter 2500 that has the standard bumper the Draw Tite hitch part # 75549 is a confirmed fit and would be a great and easy solution. Should only take about 30 minutes to install which would easily cost less than the quote you mentioned. I attached an install video for this for more info as well.
  view full answer...
• Trailer Hitch and Wiring for a 2016 Mercedes Sprinter 3500 Dually
  I did some checking and the Draw-Tite trailer hitch # 75549 does indeed fit the dually model of the 2016 Mercedes Sprinter 3500. If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right rise or drop to tow the trailer...
  view full answer...
• What Frame Width Dimension Does Draw Tite Hitch 75549 Not Fit
  The Draw Tite hitch part # 75549 that fits the 2007 Dodge Sprinter does not fit models that have a 30-3/8 inch wide frame like you mentioned. This measurement is the outside to outside width of the frame measuring from the two frame channels.
  view full answer...
• Trailer Hitch Recommendation for a 2011 Mercedes-Benz Sprinter 2500 144 inch Wheelbase
  For a hitch that has been confirmed as a fit for the 2011 Mercedes Sprinter 2500 with a 144 inch wheelbase you would want the Draw Tite hitch part # 75549. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not...
  view full answer...

Do you have a question about this Trailer Hitch?