See what our Experts say about this CURT Trailer Hitch

• Will The Curt Hitch C13238 Fit A 2016 Audi Q3?
  Hi Lawrence! I see you ordered this already, but I wanted to get you an answer to your question anyway. The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13238 will indeed fit your 2016 Audi Q3. It will fit all versions of the Q3 and Q3 Quattro for the 2016 model year, so you are good to go! We have actually installed this on a 2015 and 2017 Q3 (no 2016 yet, unfortunately) and I included the install video we did with the 2017 for you to check out. If you are going to be...
  view full answer...
• Comparing Ground Clearance Between Draw-Tite 75218 and Curt C13238 On 2015 Audi Q3
  We have not had a chance to install the Draw-Tite # 75218 on a 2015 Audi Q3 yet so I do not have the exact ground clearance measurements, but based on the two manufacturer provided installed photos I believe you are correct that it will give more ground clearance than the Curt # C13238. If you are planning on towing with your Q3 you will also need a vehicle wiring harness # 119250KIT, and a hitch ball, ball mount, and hitch pin and clip which can all be found in the etrailer Ball Mount...
  view full answer...
  
• Do I have To Cut The Fascia When Installing A Hitch On 2015 Audi Q3
  All of the hitches available for the 2015 Audi Q3 are concealed cross tube hitch designs so they all require fascia trimming. Both Class III hitches for your Audi Curt part # C13238 and Draw-Tite part # 75218 require a 3-1/2" square cut into the fascia so that the receiver portion of the hitch can stick through. I recommend the Draw-Tite part # 75218 because the installation instructions are better for this hitch. The Class II hitch available for the Audi Curt part # C12148 requires a...
  view full answer...
  
• Clearance Solution For Trailer Hitch On A 2015 Audi Q3 That Sits Too Low
  There unfortunately isn't a trailer hitch without a built in drop available for the 2015 Audi Q3 so you're only option for raising the height of the bike rack would be to use a hitch adapter like the Roadmaster High-Low Adapter for Tow Bars # RM-048-4. This adapter would give you a 4" rise to provide more ground clearance for your bike rack. Note: Hitch adapters do reduce the tongue weight capacity of the hitch by 50%, so your Curt Trailer Hitch Receiver # C13238 would have a maximum...
  view full answer...
  
• 2016 Audi Q3 Trailer Hitch Recommendation for Carrying Motorcycle Carrier
  For a trailer hitch that is confirmed as a fit for your 2016 Audi Q3 that would have enough tongue weight capacity for a motorcycle carrier we have the Curt hitch part # C13238 which is a confirmed fit and has a tongue weight capacity of 525 lbs. The etrailer part # e98873 would be a carrier that we offer that would easily carry a 300 lb bike.
  view full answer...
• Recommended Trailer Hitch Receiver and Towing Setup for 2018 Audi Q3
  We don't have a video of the Draw-Tite Max-Frame Trailer Hitch Receiver # 75218 on your 2018 Audi Q3. The biggest thing to note is the installation requires the permanent removal of the bumper beam and the hitch will replace that bumper beam for support and safety. It will require trimming your lower fascia. I've attached a photo and the installation details to assist. If you don't wish to replace your bumper beam, then I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class...
  view full answer...
  
• Draw-Tite Class III Hitch 75218 Installation on 2016 Audi Q3 for Using Hitch Bike Rack
  All aftermarket hitches made for your 2016 Audi Q3 are shown on the linked page. These options include both 1-1/4-inch Class II and also 2-inch Class III type hitches. Since both install in the same manner I recommend one of the 2-inch models, either Curt # C13238 or Draw-Tite # 75218, since these will offer broader compatibility with the available bike racks and also a higher weight capacity. Both of these 2-inch hitches will require some trimming of the rear fascia but neither required...
  view full answer...
  
• Recommended Hitch for 2016 Audi Q3 to Carry Thule Easy Fold Bike Rack
  I recommend using the Curt # C13238 which will give you a 2" receiver capable of carrying your Thule Easy Fold # TH903202. Curt hitches have a nice, durable powder coating so this hitch will stand up better to nicks and scratches than some other hitches so it's a great option that won't break the bank. I've linked a review and installation video of this hitch for you to check out, as well.
  view full answer...
• Trailer Hitch For a 2016 Audi Q3
  The Curt Class III hitch, part # C13238 is a compatible fit with your 2016 Audi Q3. Unfortunately, we don't have a picture of this hitch installed on your vehicle.
  view full answer...
• High Low Adapter Recommendation to Gain Ground Clearance for 2 inch Hitch Bike Rack
  We have the Roadmaster High Low Adapter part # RM-076 which will give a 2 inch hitch like the # C13238 you mentioned a 6 inch raise to help with ground clearance. You'd need to note that this adapter cuts the capacity of the hitch it is installed in by 50 percent.
  view full answer...
• Trailer Hitch and Wiring for a 2016 Audi Q3
  For your 2016 Audi Q3 I recommend Curt trailer hitch # C13238. This is a Class III trailer hitch with a 2 inch receiver rated for 525 pounds tongue weight and 3,500 pounds gross trailer weight. I have included a link to the installation instructions for you. To add a trailer connector I recommend # C59236 which will provide a 4-Way flat connector at the rear of the vehicle.
  view full answer...
• Where Does Curt Hitch for 2017 Audi Q3 Install Relative to the Exhaust of the Vehicle
  The crossbeam of the Curt hitch # C13238 for your 2017 Audi Q3 sits behind and above the muffler of your vehicle once it's installed. It's hard to see how everything fits together in the instructions.
  view full answer...
• Will Curt Trailer Hitch Fit 2016 Audi Q3 Quattro
  The Curt Trailer Hitch, part # C13238 is designed to fit the Q3 regardless of the model. This is a Class lll hitch and has a 2 inch receiver opening. As noted from Curt all non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps like part # 18050. Failure to properly support these loads will void your hitch warranty. If you have the tow package on your Q3 and need trailer wiring you can use part # HM40975. Without the tow package I recommend...
  view full answer...
• Installation Time Estimate for Curt Hitch C13238 on 2018 Audi Q3
  Curt Class III hitch # C13238 is a confirmed fit on your 2018 Audi Q3. On our main hitch page for your car, which is linked, we indicate an installation difficulty level of 10 out of 10, and an install time of about 1 hour 40 minutes. Curt's own instructions, which are linked for you, do indeed note 45-minutes estimated install time for an experienced installer and a similar 90-minutes for a first-time installer. The installation steps do include enlarging some attachment holes, lowering...
  view full answer...
• Trailer Hitch for 2018 Audi Q3 that Doesn't Require Hitch Adapter
  If you use a hitch adapter to change hitch size from 1-1/4 inch to 2 inch the result is that the hitch loses 50 percent of it's tongue weight capacity due to added leverage and movement. Instead the better option would be to go with a 2 inch hitch that fits your 2018 Audi Q3 like the part # C13238 which would not require an adapter.
  view full answer...
• Can Older Thule Velo Vice 589 Be Used On 2018 Audi Q3?
  I have a few options for you, but the Thule Velo Vise 589 you have can only be installed onto factory aero crossbars by using the Thule Ride On Adapter 532 which has been discontinued for quite a few years now. If you can find two of the then you can install them onto the crossbars on your 2018 Audi Q3, then install the bike rack on those. You could replace the factory crossbars on your Q3 with the Thule Roof Rack System which uses 47" Thule SquareBar Evo Crossbars # TH712200 and Evo Flush...
  view full answer...
• Trailer Hitch Recommendation for a 2016 Audi Q3
  Yes, the Curt Hitch part # C13238 that you referenced has been confirmed as a fit for your 2016 Audi Q3 so I would recommend it for you. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not include a ball mount with...
  view full answer...
• Does Bumper Have to be Removed to Install Curt Trailer Hitch 13238 in 2018 Audi Q3
  The bumper of your 2018 Audi Q3 does not have to be removed at any point in order to install the Curt Trailer Hitch # C13238. All that is required is loosening the fasteners at the bottom of the bumper cover to allow for installation of the hitch. You will need to remove the heat shield and trim it, but that will be reinstalled. In regards to the exhaust, you will need to remove the exhaust brackets and then put spacers between the exhaust brackets and the frame so the hitch can be properly...
  view full answer...
• Will the Draw-Tite Hitch for 2017 Audi Q3 Work With Threaded Hitch Bolt.
  The Draw-Tite Max-Frame Trailer Hitch Receiver part # 75218 is a great option for a 2017 Audi Q3. I do see a few reviews of others using this hitch for bike racks without reporting issue of the safety chain loops interfering with the hitch pin. That said, it does look close so it could be possible therefore I recommend using the Curt Trailer Hitch Receiver part # C13238 instead.
  view full answer...

Do you have a question about this Trailer Hitch?