9" Wide x 27" long x 11-1/4" tall. This sturdy steel fender has a slanted back, offering extra cargo clearance and making it great for your boat trailer. 16-Gauge cold-rolled steel is strong. Bolt or weld onto your trailer.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Jeff: Hello, everybody. This is Jeff at etrailer.com. Today, we're going to take a look at this single axle slant back steel trailer fender for a quantity of one. Now this is designed to cover one tire on the side of your single axle boat trailer. It'll basically act as a splash guard. It helps keep any road debris from hitting other vehicles and helps protect your trailer's cargo.
These slant back design fenders are usually used on boat trailers and when I say slant back design, I'm trying to show you if you look at it here, it's basically wider at the bottom than at the very top here. The reason they designed it that way is to leave enough room for your boat to come onto the trailer while still providing adequate coverage for your tire.If you look on the outer edge of this fender, let me just zoom in here, the outer edge has a nice finished one inch curved radius lip to it. The fender is a sturdy 16 gauge cold rolled steel construction, and it can be primed and then painted to provide even more resistance to corrosion or to match your trailer's paint finish. This is a weld-on or bolt-on installation. Now, if you do bolt it on, it does require mounting brackets.
Now, those we do sell separately. They're part number CE26061G-2. They're usually listed on this product page as a related product. This fender is made in the USA. Specs, it's for a quantity of one fender.
Application is a single axle trailer with 10 inch to 12 inch diameter wheels. As a general rule, when your trailer's loaded to its full capacity, there should be a minimum clearance of about three inches between the top of your tire on the trailer and the underside of your fender.Last thing I'm going to do is give you some dimensions. Weight on this is only about seven pounds. If we measure the length from this end to this end, it's going to be right at 27 inches long. Overall height from the bottom to the very top, right in the middle here, it's 11.5 inches tall.
Then we mentioned it being a slant back, so I want to give you the measurements at the bottom. Let me turn it this way and you'll be able to see right at the bottom is going to be right at about nine inches. Then at the very middle, the top here, it's going to be right about seven and three quarter inches. That should do it for the review on the single axle slant back steel trailer fender for a quantity of one.
Average Customer Rating: 4.8 out of 5 stars (2619 Customer Reviews)
9" Wide x 27" long x 11-1/4" tall. This sturdy steel fender has a slanted back, offering extra cargo clearance and making it great for your boat trailer. 16-Gauge cold-rolled steel is strong. Bolt or weld onto your trailer.good price good fast delivery
Works great
Had a blowout and it took a fender off. Replaced it with 2 round ones. Also replaced the taillights and a couple of clearance lights while I was working on it. Turned out great. Thanks
Very well made. I added some more bar tacks to bond the backing plate to the fender. It probably would have been fine as is, but for three minutes of effort I know that the two won't separate. I built a T out of 1" tubular steel to mount it to the trailer and there is no flex, once I welded it all together. Arrived clean enough to paint (but I still wiped it down with isopropyl alchohol before painting).Nice heavy gauge fender.
Replaced an existing fender that was too small. Easy to install. Painted with a cold galvanized paint and has held up very well for the year it has been installed.
These Trailer Fenders are a quality product which are "rust free". It's hard to find an 8" rust free wheel fender on-line. All stainless steel fenders listed on line require you to paint them so they will not rust. This is because since they were stamped/pressed via large machine press at the manufacturing plant, using a flat sheet of stainless steel. When the sheet is pressed it's damaged and will rust.
The fenders themselves were fine. After having them installed for a while one of the backing plates fell off. I contacted etrailer and they sent me a new fender. I removed the backing plate from that one and riveted on the trailer. No problems since.
I used these steel fenders to replace aluminum fenders on my utility trailer after one had fallen off along the road somewhere. Prior to installing these I painted them with Krylon Fusion gloss hammered metal spray paint, which has held up well.
On the fly I had to make a change... not a problem they handled it very easy, Thanks guys! Here is what I am using them for
It was the full set of dimensions in the description that sold me as to what I needed. The steel fenders were short on finished dimension size.
Great looking and functioning fenders. Really thought I would never find fenders for a 1993 boat mate trailer that would fit but these fenders fit great. Sure made my trailer look better.
These fenders were to replace the rusting out fenders on my Four Winns boat trailer. They really spruced it up! The only "modification" I had to do was add an extra 3/8 nut on both sides between the fender and the trailer frame to make it fit. I used all new stainless steel fasteners.
Great looking fender. An asset to any trailer.
Great product. I use them all the time for wheel wells.
They worked out great. However the trailer was overloaded and the fenders came down onto the tires ,so the guy who owned the trailer cut the brackets off instead of just unbolting them.
I have to go pickup the trailer and remake the mounting brackets to make them able to just bolt on.
This was used on a box trailer. I had a tire blow out and seriously damaged the original fender. This replacement fit perfectly and looks like the original. Service was also great.
Purchased these replacement fenders 1 year ago for a 20+ year old trailer to replace the original rusty ones. They were a perfect fit and welded on easily. Still looking good 1 year later.
The photos on the website show the backing plate attached symmetrically to the fender. The ones I received had the backing plate attached at an angle (left side 4" from bottom of the fender to the bottom of the backing plate - right side 1" from the bottom of the fender to the bottom of the backing plate). Mounting the fenders symmetrically front to rear would create attachment problems. I am having trouble convincing Customer Service this is an issue.
Bought these for my new log splitter they worked great just need pain now . Good product and really good service
I bought a boat trailer fender. I haven't mounted it yet but it looks good and was a very reasonable price. Great variety and Prompt shipping. I'm very satisfied.
Fit perfectly for my application. Very strong, I step on them regularly. Smooth surface than accepted primer and paint well.
I put two of these fenders on my canoe trailer. Both broke before I'd gone 1,000 miles.
Do you have a question about this Trailer Fender?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.