Single Axle Trailer Fender for Enclosed Trailers - Cold Rolled Steel - 15" Wheels - Qty 1
(1847 reviews)
Price: $64.35
In Stock
Single Axle Trailer Fender for Enclosed Trailers - Cold Rolled Steel - 15" Wheels - Qty 1
Item # HP29VR
Our Price: $64.35
Orders above $99 qualify for Free Shipping
In Stock
Need help with installation?
Locate installers near me- All Info
- Reviews (1847)
- Q & A (0)
- Photos
- Why etrailer?
etrailer Trailer Fenders - HP29VR
- 15 Inch Wheels
- For Single-Axle Trailers
- Bolt-On
- Weld-On
- Steel
- 32 Inch Long
- No Step
- 10-3/4 Inch Wide
- etrailer
10-3/4" Wide x 32" long x 15-3/4" tall. This sturdy, rounded fender has a flat back to mount flush with your enclosed trailer. 16-Gauge, cold-rolled steel is durable. Bolt or weld onto your trailer.
Features:
- Rounded fender covers 1 tire on your single-axle trailer
- Blocks road debris from hitting other vehicles and helps protect your trailer's cargo
- Flat mounting flange on inner edge lets you mount fender flush with your enclosed trailer
- Close fit keeps dirt from building up between the fender and trailer
- 1" Wide outer edge is rounded
- Sturdy, 16-gauge, cold-rolled steel construction
- Prime and paint the fender to get corrosion protection and to match your trailer's finish
- Weld-on or bolt-on installation
- Requires drilling and purchase of mounting brackets (sold separately) for bolt-on installation
- Made in the USA
Specs:
- Application: single-axle trailers with 15" diameter wheels
- Dimensions: 32" long x 10-3/4" wide x 15-3/4" tall
- Quantity: 1 fender
- Weight: 9 lbs
- 1-Year limited warranty
Tips for Replacing and Installing Trailer Fenders
- Do your best to match the dimensions of the new fender to your old one.
- If a fender was damaged during a blowout, use the opposite fender to get the dimensions.
- As with all trailer maintenance, don't forget to chock your wheels before getting started.
- For a bolt-on fender, use your existing mounting hardware, if possible.
- The old mounting bolts or screws might be stripped or rusted, in which case you'll need to tap them out and buy new hardware.
- If removing an old, welded-on fender, either carefully chisel it off yourself or take your trailer to a weld shop to have the fender professionally removed.
- Don't forget to prime and paint the new fender to keep it from rusting (and to match your trailer's finish).
- Before you start drilling, position the fender where you need it and center it over your wheel well.
- Mark where you need to drill (measure twice, drill once).
- Don't tighten down the mounting hardware completely until you're sure the fender is mounted correctly.
MFS00001 Single Axle Trailer Fender - 90-Degree Back - Cold Rolled Steel - 15" Wheels - Quantity 1
Replaces F1075X32-1R
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Did not arrive in time
- Arrived Damaged
Customer Reviews
Single Axle Trailer Fender for Enclosed Trailers - Cold Rolled Steel - 15" Wheels - Qty 1 - HP29VR
Average Customer Rating: 4.8 out of 5 stars (1847 Customer Reviews)
10-3/4" Wide x 32" long x 15-3/4" tall. This sturdy, rounded fender has a flat back to mount flush with your enclosed trailer. 16-Gauge, cold-rolled steel is durable. Bolt or weld onto your trailer.by: Rich B.07/09/2012
These fenders are excellent. The stamping and finish is perfect. They arrived at my house well packaged and damage free. I bought these as an alternative to finding NOS fenders for a 1946 Bantam Jeep trailer I am restoring. They are 2 inches wider than the originals but that's a good thing since I can run more modern wheels and tires without them sticking out of the fenders. Otherwise they are exactly the same as the original fenders except stronger due to the lip on the body side of the fenders. I am very pleased with my purchase and the service I received from etrailer.
by: Steve F10/04/2022
I'm very pleased with the fender and your service. All the measurements were right there on the website so I could plan accordingly. Etrailer even upgraded my shipping at no extra cost!
by: Mike01/03/2023
This is a rating of a replacement fender for an identical fender purchased years earlier. The original fender was sturdy and tough. This purportedly identical part is nothing like the earlier purchased part was. It bends and dents too easily. I could sit on the original, this one folded when I sat on it. I have not measured it, and I suspect a much thinner metal was used. Booooo. I wanted the sturdy fender I originally bought. Covid and steel prices resulted in this flimsy version, I think. I do not approve.
by: Kevin01/12/2018
Wow, very impressed with the service and shipping time from etrailer. 3 day shipping showed up in 2 days. Both fenders came in one super sturdy box, very well packaged. No dings or dents. Fenders are very thick gauge metal and not flimsy at all. These fenders are very wide at 10.75" but that's exactly what I needed for my application. No complaints at all, I couldn't imagine a better quality fender.
by: Brian C08/25/2017
These fenders are very sturdy. I used them on a trailer I recently built. I mounted with 2 pieces of angle iron front and back. I am very satisfied.
Comments
Fenders are holding up very well.
Brian C - 08/28/2018by: Jamel05/04/2018
I was looking to make a custom rear fender for my 2017 Polaris Slingshot SL 3 wheeled roadster and came across the etrailer website. I looked at many different types and styles of fenders before I finally decided on this one. Judging by my preliminary test fitting, it looks like it will fit perfectly once I fabricate the mounting brackets.
I received my fender within a few days after placing my order and it arrived damaged free thanks to the large box it was packaged in. I will definitely be buying more fenders from etrailer in the future.
by: William03/31/2020
I am very happy with the product; easy to work with it; I modified it cut it to size to accommodated new 15" tires for my enclosed trailer.
Picture of the original trailers fender 13" (on the left side) side by side with F1075X32-1R fender modified
Thank you
by: Greg07/05/2013
Very happy. Sturdy fender with an ample lip for attaching hardware.
I trimmed it a little and used it for a hot rod jeep with a fabricated bed.
Great part, would (will) use again.
Comments
Any more info on your killer little rig, er, I mean, your fender installation? wink wink?
-- comment by: Robert - 06/19/2014Still very happy with the fenders, and etrailer in general. Great supplier.
Greg - 07/05/2014by: Brad 10/27/2022
Nice quality construction and quick shipping. Kept up to date on shipping status the entire time.
by: Daniel10/01/2018
I totally rebuilt my trailer from the ground up new paint and new sideboards new coupler new bearings and of course new fenders from etrailer really finished it off! The fenders painted up like nothing and look great!
by: Dean C03/02/2017
I will qualify right from the start, this is not just a product review. This is a review of my overall experience with etrailer.
Let's just say my order had some shipping issues that delayed it. I had to have the fenders for my trailer asap.
After discussing the issue I had with my order, the members of the etrailer team responded. In a very positive way!
Michelle S worked to get my order expedited and I received my fenders on time, undamaged and looking great! Thanks Michelle!
I dont judge a company by just the product it sells, I judge a company by it's products and customer service. Let's just say I was thrilled to get the fenders fast and thrilled they fit and looked great installed.
Etrailer staff you earned a customer for life!
by: ERG04/08/2022
Of all the online vendors to buy from I chose etrailer because it was easy to find the size I wanted without having to sort through a bunch of things I didn’t need. The fenders arrived quickly and well packaged. They are nice quality and as described. Price was very good compared to other places as well.
by: Craig 12/14/2022
Just what I needed , great price and se rvice
by: Kurtis 11/22/2022
Fast service with better pricing then anyone else around me.
by: Chris R.08/17/2016
Fender worked like I needed it to. I cut the fender in half to make two shorty fenders for my kayak trailer. They work great!
by: John R06/21/2018
Disappointed with the rust and other blemishes on the fender. It is described as being silver in color (which I guess it is, since that's the color of rolled steel), but the implication is that there is a finish on the fender, not just raw steel, and there is no indication in the description that the fender needs to be painted.
by: Charles 02/02/2022
Quick delivery and good quality product. Needed fenders for wider tires and etrailer had what I needed. Glad I found this website.
by: Jd11/11/2022
Great Service !
by: Jon H.06/09/2012
Ordered the product, got here in 4 days,and will be putting them on the Teardrop Trailer today. Highly recommend etrailer to my DIY customers and have used it about 10 times myself, very satisfied.
by: Himmy11/30/2016
I ordered this fender as it was the only one I could find that was wide enough.
The fender has one straight 90degree side. I would have preferred the rounded edge on both sides but with the width issue it will do. The edge with the 90 is a little wavie and since it will be exposed it's a little bothersum. I cut it in half to make two short fenders. It looks like it's gonna work
by: Andy B.11/24/2014
These fenders are solidly made and with a little trimming in overall length will fit my application. Items were well packaged and arrived within a few short days of ordering.
by: Edward 10/23/2020
Nice raw metal fender, formed smooth & consistence. Extra wide for the wider type tires & easily mounted.
Comments
Working out great, made out of good material, strong enough to sit on.
Edward - 10/24/2021by: Delbert06/04/2022
Excellent handling and shipping time. Well packaged and everything arrived in the box.
by: Ken05/14/2022
Great fenders, they are actually 10 and 3/4 in wide
25
1840
Show More Reviews
See what our Experts say about this etrailer Trailer Fenders
- Recommended 32 Inch Steel Weld-On Trailer Fender for 14 Inch TiresThe closest option we have available to the dimensions listed in your question is with a Single Axle Trailer Fender like the etrailer # HP29VR. This 16-gauge steel fender is a weld-on application for 14 to 15 inch wheels. It measures 32 inches long, 10-3/4 inches wide, and 15-1/4 inches tall. It features a 90-degree angle on the back for mounting onto your trailer and is made right here in the USA. I have attached a short video demonstration on this fender, along with a link that will...
view full answer... - Single Axle Trailer Fender 32 Long x 10.75 Wide x 16.25 TallIf you are referring to a trailer fender that is 32" long x 10.75" wide x 16.25" tall then the best option we have is the Single Axle Trailer Fender part # HP29VR which is 32" long x 10.75" wide x 15.25" tall. This fender is made of 16 gauge steel right here in the U.S.A. It is designed for 14-15" diameter wheels but can be adjusted for different sizes. It will be the closest option we have to what you are looking for. I have attached a review video for you as well.
view full answer... - Can the etrailer Single Axle Trailer Fender # HP29VR be Screwed on Instead of WeldedIf you are okay with putting some screws through the Single Axle Trailer Fender # HP29VR that can secure it for travel then I see no reason why not. It is classified as a weld-on application because there are no places that have been made for screws so you will have to install them through the finish which may not look as great as a weld-on installation would. I recommend securing it in at least 3 places if you go this route; both of the sides and one in the middle.
view full answer... - Trailer Fender Recommendation for Tire Size 30x10.5R15For a fender that will fit your tire size well we have the part # HP29VR. This fender measures 32 inches in length, 10-3/4 inches in width and is 15-1/4 inches in height. It would basically be just a bit wider and longer than your tire size so it would be a nice fit.
view full answer... - Is the 90 Degree Side of the 16-Gauge Fender Flat Enough to Mount Two Side by SideI went out into our warehouse and took two 16-Gauge Steel, Single-Axle Trailer Fenders # HP29VR and put them next to each other and found that they match up perfectly. The 90 degree side is is flat so when you put them next to each to each other the flat surfaces line up.
view full answer... - Trailer Fender Recommendation to Replace a 10 X 33 X 17 FenderFor a metal fender pretty close to the dimensions you listed check out the Single Axle Trailer Fender # HP29VR. The dimensions of this fender are 10-3/4" wide x 32" long x 15-1/4" tall. I attached a review video for this fender for you to check out as well.
view full answer... - Selecting Various Parts Needed for 9 x 20 BBQ Pit TrailerIt is not possible for me to know which specific parts are necessary for your particular bbq pit trailer but you can see item pricing on each product's page. I have included links to our department pages for spindles, bearings and bearing kits, leaf springs (both slipper and double-eye types), hangers, fenders and trailer lighting. On each page there are filters that allow you to sort and narrow the results based on the particular types and sizes of parts you need. I also linked two...
view full answer... - Are the etrailer # HP29VR Single Axle Trailer Fenders Sold In Pairs or IndividuallyThe Redline # HP29VR trailer fender you referenced is sold individually. For a pair, you'd need to order two of that part number. If you'd care to see a product description video, click the link I've provided.
view full answer... - Recommended Steel Double Radius Trailer Fender 30 Inch LongThe best option I have for you is the Single Axle Trailer Fender part # HP29VR which measures 10-3/4" wide x 32" long x 15-1/4" tall. It is made of steel, has the double radius sides, and is designed for wheels 14" - 15" diameter. I have attached a full list of our steel trailer fenders for you as well.
view full answer... - Fender Replacement for a 2012 Forest River R-PodThe etrailer fender part # HP29VR is 10-3/4" Wide x 32" long x 15-3/4" tall and would be the closest option we carry to what you are looking for.
view full answer... - Do You Have Fenders with a Backplate or Mount IncludedSomething like part # HP36VR is probably what you are looking for. It is designed to fit 14-15 inch diameter tires and has a back that is spot welded to the fender.
view full answer... - Availability of a Steel Trailer Fender with a 1 Inch Radius Lip on Front and BackWe do have one model that has the 1 inch lip radius on both sides. Take a look at 16-Gauge Steel, Single-Axle Trailer Fender, 1 inch Radius Front/Back, # HP89VR. There are some differences though. This fender is 7 inches wide, 28 inches long, 10 inches high, and fits 13 or 14 inch tires.
view full answer... - 13 inch Wide Steel Trailer Fender RecommendationWe do not custom make fenders here, but we do carry a fender that is 13 inches wide that is similar to the # HP29VR that you referenced. Check out the part # HP66VR. This fender is 4 inches longer than the one you referenced but it is 13 inches wide. I attached a review video for you to check out.
view full answer... - 32 inch Long Trailer Fender that Can be Bolted OnI have a better solution for you, for a fender that would be easier to drill and bolt on than the # HP29VR that you referenced I would recommend the # HP36VR as this fender is the same size as the one you referenced except it has a flat back on it without a radiused lip that would make drilling and bolting much easier.
view full answer... - Availability of Wider than 12 inch Steel Trailer FenderWe don't have the ability to custom make fenders but we do have the part # HP66VR which is a 13 inch wide fender and uses 16 gauge steel.
view full answer... - Availability of Fenders for Use as Replacements on 1988 Jeep Comanche Pickup with Dump BodyWe carry general-purpose replacement trailer fenders including plastic, aluminum and steel products, all of which are shown on the linked page. You can click on the filters on the page to select your required length dimension (32-inches long overall), your wheel (not tire) diameter, and the preferred material. For example, in a 32-inch length steel fender with a backing plate and radius lip that will work with a 15-inch wheel you could use Redline # HP36VR. This fender measures 32 L x...
view full answer... - Recommended Single-Axle Trailer Fender That Can Be Bolted On Aluminum TrailerThe etrailer brand Trailer Fender you referenced, part # HP29VR, is designed to be welded on, but some customers have drilled through the small lip on the fender when installing. We do have another option that may work for you. I recommend the etrailer brand Trailer Fender With Backing, part # HP36VR. This fender, like the fender you referenced, is a single-axle fender made of 16 gauge steel, and is designed for 14 to 15 inch wheels. I have attached a product review video for this fender...
view full answer... - Aluminum Tread Plate Trailer Fender # HP96VR RecommendationIf you are looking for a fender for your trailer that will resist corrosion I would recommend the Aluminum Tread Plate Trailer Fender # HP96VR as it is made of aluminum and will resist corrosion more than steel. The 16-Gauge Steel, Single-Axle Trailer Fender # HP29VR that you referenced is not galvanized and would be a lot more susceptible to rust and corrosion than the # HP96VR .
view full answer... - Replacement Fenders for 2001 Single-Axle Vent Trailer with 15-Inch WheelsWe can offer you a choice of steel, aluminum or even bracket-mount plastic replacement fenders that will work on your single-axle trailer with 15-inch wheels. You also have a choice of fenders that include steps if you like. The linked page will show you all trailer fenders that will work with 15-inch wheels and the filters on the page will let you sort the results based on your preferred material, features and installation method. If you prefer a weld-on steel fender without a step we...
view full answer... - Is the Steel 14-15 Single Axle Trailer Fender Offered with a BackingThe Single Axle Trailer Fender part # HP29VR is offered with a backing using part # HP36VR.
view full answer... - Replacement Trailer Fender For Single Axle Travel Trailer That has 30" X 10" FendersThe Single Axle Trailer Fender # HP38VR is the closest we have a 30" long and 9" wide. If that is not wide enough you will need to move up to the Single Axle Trailer Fender # HP29VR that is 32" long and 10-3/4" wide. Both of these are metal so you will not have to deal with them cracking or becoming brittle and damaged by UV rays.
view full answer... - Mounting the Aluminum Tread Plate, Jeep-Style, Single-Axle Trailer FenderThe Aluminum Tread Plate, Jeep-Style, Single-Axle Trailer Fender, item # HP96VR is designed for a weld on application and putting screws and washers through the lip on the inside of the fender would most likely not last. If these fenders were to be installed on a steel trailer you would need to have an aluminum mounting bracket welded to the inside edge of the fenders that could be used to stiffen the fender and give additional mounting points. We do have steel fenders available that should...
view full answer... - Can etrailer Aluminum Tread Plate Trailer Fender Fit Boat TrailerThe etrailer brand Aluminum Tread Plate Trailer Fender, part # HP96VR measures 10 inches wide by 33 inches long by 17 inches tall and is designed for 13 to 15 inch wheels. This is a weld-on or bolt-on application. To install on your boat trailer you will need to consider how it is to be attached, and how much of a mounting surface you have. I have attached a link to an installation video for this fender you can check out. I recommend using a professional welder if that is the route you...
view full answer... - Recommendations For A 10" x 32" x 17" Polished Trailer FenderThe fender we have that matches your needs the closest will be the Single Axle Jeep Style Trailer Fender # HP96VR. This has a polished diamond plate aluminum finish and measures 10" Wide, 33" long, and 17" tall, but is the boxier and squared Jeep style look. If that doesn't suit you, the only other options we have that will be similar in size will be the Ribbed Steel # HP49FR and the Cold Rolled Steel # HP29VR. Both of these will measure 10-3/4" Wide, 32" long, and 15-1/4" tall, but will...
view full answer...
Do you have a question about this Trailer Fender?
Why etrailer.com?
At etrailer.com we guarantee:Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.Most detailed, accurate trailer fender information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.Returns Policy
Need to return an item? No problem. Please read our Returns Policy for more information.
Info for this part was:
Edited by:
Lindsey S
Installed by:
Jeff D
Expert Research:
Jameson C
Written by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.