When your trailer is over 80" wide, visibility isn’t optional—it’s required. This Mini LED Identification Light Kit makes your trailer easy to spot on the road by clearly showing its full width to other drivers. Each 1" diameter light uses a red LED behind a red lens, meeting FMVSS 108 standards for safety compliance. The low power draw of just 0.06–0.08 amps per light keeps your electrical system efficient, and with up to 100,000 hours of rated operation, you can count on long-term performance without bulb changes or dimming over time.
If you use your trailer around water, these lights are built for it. Each unit is IP68 rated and fully sealed, so the housing and lens form one waterproof piece that blocks moisture from reaching the diode or circuit board. TecNiq’s urethane potting adds another layer of protection against corrosion and dust, lasting longer than common epoxy seals. Whether you’re launching a boat or driving through heavy rain, these lights stay watertight and reliable.
Rugged conditions demand tough materials. These lights use an automotive-grade polycarbonate lens that’s impact-resistant and UV-stable, keeping them clear and strong even after long exposure to sun and debris. The military-grade circuit boards inside are built for vibration resistance, so they can handle rough roads without flickering or failure. With this level of durability, these lights keep shining bright through every haul.
You don’t need extra brackets or complex wiring. Each light mounts easily into a standard 3/4" hole in any orientation using a recessed design that keeps things neat and protected. The 48" hardwired leads give you plenty of length for connection, and since they tie directly into your running light circuit, setup is straightforward. Once installed, the compact 1" round housings sit flush and clean while providing reliable identification lighting for the long haul.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody, this is Jeff at etrailer.com. Today we're gonna take a look at the mini LED ID lights with the red lens over for over 80-inch-wide boat trailers, and this is for a quantity of three lights. Now you can see, these are a small round LED light that'll serve as a rear identification light for your trailer that's over 80 inches wide. It is required by law to have rear identification lights, if your trailer exceeds 80 inches wide. Now these are a sealed waterproof housing and lens unit, which is submersible, does have an IP 68 rating, which means it's resistant to submersion up to a maximum depth of five feet underwater for up to 30 minutes. They do use a military grade construction circuits boards for these lights.
They use a urethane potting, which gives you better protection than the common epoxy potting. And the LEDs they use are premium LEDs, which are energy efficient, long lasting and vibration resistant. They are rated for up to 100,000 hours of operation. The lenses are a nice durable UV-resistant lens, and it is a red lens over a red LED. Now at the end of this video, I am gonna hook this up to some 12 volt power, just to show you how bright the lights are.
These are compatible with 12 volt DC system. They are a recessed mount installation with the included grommet you can see already installed. They will require a 3/4 inch size diameter cutout to fit into, and we also even sell stainless steel trim rings separately, if you want those for a nice finished look, and they are usually listed on this product page as a related product. Now this does hardwire to your application. It is a two-wire design, has a ground and a power wire and the wire length totals about 48 inches.
This does meet or exceed the Federal Motor Vehicles Safety Standards, 108 standards. It is for a quantity of three lights. Input voltage per light is 9 volts to 14 volts, power draw per light is 0.06 to 0.08 amps. And the size of the light itself, we'll put a ruler on it, the diameter is right at one inch and the total depth of it is right about 7/8 of an inch. So what we're gonna do now is I'm gonna go ahead and hook this up to some 12 volt power.
Once we get it hooked up, go ahead and turn on the power. And you'll see all three of the lights light up. If I turn off the overhead lights, you can see how all three of them there light up, give you a very, very bright red light. And even if I zoom out, you can see how these would look when they're installed on the rear of your trailer. Go ahead and turn back on our overhead lights, go ahead and turn off our power. But that should do it for the review on the mini LED ID lights with the red lens for the over 80-inch-wide boat trailers..
Ratings & Reviews
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.