Jensen Antenna - Top or Side Mount - Rubber Mast

Part Number: 44US01R

311 Reviews | 31 Questions

In Stock

$34.12

Retail:$40.24

You Save: 15%

Add to cart

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

jensen rv antennas radio roof side antenna - top or mount rubber mast

jensen rv antennas radio antenna - top or side mount rubber mast

Show All (9) Product Images

Show Fewer Product Images

Customer Photos

Jensen Antenna - Top or Side Mount - Rubber Mast customer photo

Show All (1) Customer Images

Show Fewer Customer Images

Videos

Complete Breakdown of the Jensen Antenna

Show All (1) Videos

Show Fewer Videos

Need help with installation?

Locate installers near me

Great Prices for the best rv antennas from Jensen. Jensen Antenna - Top or Side Mount - Rubber Mast part number 44US01R can be ordered online at etrailer.com or call 1-800-940-8924 for expert service.

Jensen RV Antennas - 44US01R

Jensen AM/FM antenna
Rubber mast
Top or side mount
Overall dimensions: 2-3/4" diameter x 16-1/2" tall
Cable length: 8'3"
1-Year warranty

44US01R Jensen Rubber Mast Antenna - AM/FM - Top or Side Mount

Video of Jensen Antenna - Top or Side Mount - Rubber Mast

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.

Video Demo Jensen RV Electronics 44US01R

Complete Breakdown of the Jensen Antenna

Video Transcript for Complete Breakdown of the Jensen Antenna

Today, we're going to take a look at the Jensen top or side mount black rubber mast antenna. Now, this is an AM/FM antenna, it's black in color, has a rubber mast. It is a top or side mount, and you can do that like right now it's set up for a top mount. For a side mount, all you have to do is take a screwdriver to the screw right here in the side, just loosen it up, and that'll allow you to rotate it. Then go ahead and tighten it down that way. Then with it tightened that way, you can see now it can be used as a side mount antenna.

The cable length it comes with is a little over eight feet long. It does have a ground wire with it. It does include all the mounting hardware to install this. Just the overall dimensions, total length on the mast itself is about sixteen and a half inches tall, the diameter on the mounting section is about two and three quarter inches in diameter. That should do it for the review on the Jensen top or side mount black rubber mast antenna..

Customer Satisfaction Score:

98% were satisfied with this product

2% of customers were not satisfied

Product did not meet expectations
Wrong item was ordered
Too difficult to install

2% of customers were not satisfied

Product did not meet expectations
Wrong item was ordered
Too difficult to install

4.8

311 reviews

5 Stars		(259)
4 Stars		(40)
3 Stars		(6)
2 Stars		(2)
1 Star		(4)

by: Will 04/26/2025

Replaced broken one on toy hauler matched identical to factory and no issues with replacing. Sealed it up and radio is back in action replaced it as we did a Crazy Seal roof coating install today!

Click to Enlarge

Gwendolyn Y.

4/29/2025

Love to hear it, Will! What kind of music do you turn into on the radio?

by: Tracy 04/22/2026

Antenna was not an improvement to my radio but the service at etrailer was great would definitely use etrailer again

by: Mark 06/08/2026

Great customer service and have been very happy with my purchased items.

by: William 05/10/2026

Perfect replacement from original that broke

by: Rick 10/06/2025

I only needed the rubber mast to replace the already installed antenna on my 2013 Itasca Sunstar 27N Motorhome. I was able to merely screw the new rubber mast onto the the existing base, after removing the broken one. I saved all the additional hardware supplied for possible future use, if ever needed.

by: Michael 09/22/2025 One Year Later

Ordered as a replacement for one that broke, just needed the top part. Was a direct replacement.

by: Gordon 06/23/2025

Direct replacement for our truck camper roof mounted am/fm antenna. The last one stood up to 14 years of service. Hoping the same for this one. Looks good to me.

by: Richard 11/23/2025

Plug and play. High quality. Works great.

by: Rick 12/29/2017

I chose to purchase a Jensen 44US01R antenna for a used travel trailer we recently purchased that did not come equipped with a radio antenna. etrailer had the best price around and free shipping on a $50 purchase. My antenna arrived promptly and I found the antenna mast was bent (rubber). It was properly packaged, so I called to ask if that is the way they were made. I was informed it should be straight and that they would replace it. Now this was not expected on my part considering it was a usable part. etrailer went above and beyond my expectations to make me a satisfied customer. Installation was easy and it seems to work well. Hopefully it will hold up to the elements over time. Thank you etrailer!

Rick One Year Later

12/29/2018

My Jensen antenna has held up well and seems to work okay for what it is.

by: Ray 05/04/2026

Exact fit and quick shipping

by: Bryan 12/24/2021

The antenna is exactly what I needed. Works great and will now last a long time. Unfortunately the original installation was done by someone requiring max supervision. Water under the bridge.
I gave four stars because I feel that since this antenna is advertised for an RV replacement antenna there should be an option to purchase antenna cables at longer lengths. I needed 18 feet to pull through to the radio.
As always, etrailer is my go to place for all of my RV and trailer needs. Thank you to all the fine professionals at etrailer that make my life simpler. Merry Christmas.

Jenny N.

12/28/2021

I do have an alternate antenna for you. It is part # AN519 and it has an 180 inch long cable. It has the longest cable of any of the antennas that we carry.

Helpful Links

RV-AntennasJensenAN519.html

Bryan One Year Later

12/27/2022

Great For an RV needing an extra long cable connection

by: Larry K. 02/17/2018

I needed a antenna tower to match my feed cable which was run through the walls of my RV. Otherwise I would have had to fish a cable through a thin wall (No Fun!!!). This antenna had the identical match and saved me a lot of time! Was sent the day I ordered and I got it in 2 days. Very Happy with etrailer!!!

Larry K. One Year Later

2/17/2019

For an aftermarket antenna, I think it was better quality than the original. Doing fine, well made. Worth the small amount of money!!

by: John 06/27/2025 One Year Later

ordered this antenna to replace a broken one, it was a flawless replacement, looks good and works good.

You should buy this!

by: Richard 04/28/2025

I was dubious that the antenna for my Lance camper listed by etrailer could be the correct one, I mean the camper is 5 years old so what are the odds. PERFECT fit... in fact I could just install the components needed, no need to open the roof.

by: John 06/06/2025 One Year Later

Works great near any urban area. Gets multiple channels automatically

by: Cheltzy 01/10/2026

Great company to work with. Shipped quickly and arrived on time.

by: Daniel 06/19/2025

I needed to replace the exterior radio antenna for my Rockwood HW trailer. This was the perfect fit!

by: Fred 05/22/2018

2016 Toyota Tundra

5 stars for service and the antenna looks right, but waiting for the rain to stop before I can install it.

One star off on the product since there is no information/instructions on installation.
Appears to be pretty straight forward, but two plates and assume one goes under the outside skin and one on the inside, but not sure how to seal it. Butyl tape or not?

Mike L.

5/23/2018

Silicone caulk is whats recommended, due to the fact that it stays flexible for a long time.

by: Eddie 12/24/2025

Works well

by: Richard 07/29/2018

Product arrived safe and as scheduled. Installed on truck camper that had a stickum type of antenna where the AM/FM reception was so-so. No instructions included but wasn't necessary for installation. Hardest part of installation was drilling holes in the side of the camper. As only a suggestion, use clear silicone on base plate before tightening down screws and finishing the installation to prevent water penetration.

by: Michael 05/12/2025

2022 Forest River Wildwood Heritage Glen Travel Trailer

no trouble installing took less than five minutes . it took longer to unfold step ladder than putting on

by: Michael 01/28/2020

Purchase this antenna to replace a tall 36” chrome antenna that was damaged on top of my motor home. My previous antenna had a spring base but kept getting hung up on the top of the garage door damaging the base of the antenna. I chose this antenna after seeing similar antennas on other motor homes. I receive great reception with this antenna.

Michael One Year Later

1/31/2021

working great. Great reception

by: Donna 05/08/2019

Item as described nicely packaged for shipping .Shipping was fast. It is replacing the antenna on our Lance trailer ( Jensen Stereo) it is the exact one that came with our Trailer new. It broke only do to our stupidity of not unscrewing it and taking it off before putting the winter cover on our trailer.

by: William 06/12/2020

I am not just writing about this product, but rather about the excellent service that is provided by this company. I have ordered a lot of "stuff" from etrailer and sometimes I have technical questions and the support is there. Sometimes I have had issues with a product being delivered damaged (shipping issue no doubt) and support is there. Overall, etrailer deserves more than 5 stars for always doing there best to look after legitimate customer issues with the products they sell. The follow up after sale is second to none and would recommend them highly. It is why I keep coming back!

by: michael 08/22/2024

Haven't installed it yet. The mounting surface on my 1962 Econoline is curved and this mounting plate is flat and rather large. I need to source some dense foam or come up with a way to make the plate fit the curved cowl. If on a flat surface, this antenna would fit great. This is my issue, no fault of eTrailer. The antenna seems to be excellent quality. Everything you need is included.

311

true

Show More Reviews

See what our Experts say about this Jensen RV Antennas

Do you have a question about this RV Antenna?

Can Self Tapping Screws Be Used To Install the Jensen RV Antenna Part # 44US01R
The Jensen Antenna part # 44US01R comes with bolts/nuts not self tapping screws. However, you can add these using part # 1131832 (3). In regards to strength, the self tapping screws will hold the antenna just fine on your roof so there will be no issues here.
view full answer...
What RV Antennas Have a Rubber Mast/Mount?
Hi Jim, From what you're describing it sounds like you want something with a rubber gasket for waterproofing like that they have on cars. We have two antennas with that option, but they are significantly shorter than the AN110 you were looking at. The AN110 installs using a bracket due to its height and retractability, which is why these other antennas are shorter due to how they mount and the fact that they're not retractable. I will list them out below for you to take a look at: -...
view full answer...
Can Just the Mast Be Replaced On Rooftop Antenna for RV Stereo
We do offer various different antennas for RV stereos like the Jensen Antenna part # 44US01R or part # JAN139. The difference mostly comes down to mast length, mount type, and cable length. The actual plug which goes into the stereo is universal so you don't have to worry about brand. That said, the actual mast is specific to the base which means you can't usually just replace this part so you'll need a new unit if yours is gone or damaged. I have attached our full list of antenna options...
view full answer...
Can I Buy Just the Jensen Antenna or do I Need to get a Whole New Kit?
Hello Les, Thanks for writing in. I reached out to Jensen, and unfortunately, they confirmed that the individual antenna parts are not available separately. They also could not confirm that the rubber mast from a new Jensen Antenna # 44US01R can be removed and swapped over to your existing ball mount. Since Jensen can't verify that the parts are interchangeable, I don't want to tell you that it's as simple as removing the screw at the ball and swapping the antennas. The best option is...
view full answer...
How To Deal With A Roof Mounted Antenna When Putting On Your RV Storage Cover
Hey Tom, Typically you'd just bend the antenna down and have the cover sit over it. That's completely dependent on the length of the antenna and its flexibility though. If bending down isn't an option I'd just see if I could replace the antenna with one that has an adjustable base like the Jensen # 44US01R so that you can lay the antenna flat against the roof when the cover is being used. I would not cut a hole in the cover and add a grommet since this would likely just lead to a leak...
view full answer...
Is There An RV Antenna With 2 Or 3 Foot Long Cable?
We do have Jensen In-Wall Antenna - AM/FM - 6' Long # AN140 which is 6 feet long total, but it comes with a threaded on wire loom to hardwire to an antenna, and it can be removed which leaves you with about 3 foot long cable that would work for you and thread right into your new antenna without hardwiring anything. We also have Jensen Antenna - Top or Side Mount - Rubber Mast - 6" # JAN139 which is an antenna with 44-3/4" long cable.
view full answer...
Can You Buy just the Mast with Ball Mount for the Jensen Antenna # 44US01R?
Hello Michael, Jensen does not sell just the half ball mount, you will need to purchase the Jensen Antenna - Top or Side Mount - Rubber Mast # 44US01R for that piece. I am very sorry that that is not a replacement part. What kind of camper is this going on? Any big trips in the near future? If so, where are you headed?
view full answer...
How To Install The Jensen Antenna With Rubber Mast On An RV
To install the Jensen Antenna - Top or Side Mount - Rubber Mast # 44US01R you'll need to drill a hole about 3/8" wide to fit the coaxial cable connector through into your RV. You'll also need to pre drill some holes for the mounting screws using a 7/64" drill bit since the included screws aren't self-tapping. You'll place the black gasket on the antenna over the coaxial connector and you will place the white gasket on the inside of the RV. Then run the screws through and tighten them up...
view full answer...
Replacement AM/FM Radio Antennas For a 2016 Thor Challenger 37LX Class A RV Motorhome
Here is a list of the Jensen radio antennas we currently carry. You can compare these with the one on the roof of your 2016 Thor Challenger 37LX to determine if we have an exact replacement or if you will need to remove the antenna from your roof to install a new antenna. Most all radio antennas will use the same style connector going into the stereo if you replace the antenna cable as well. Jensen Antenna - Top or Side Mount - Rubber Mast # 44US01R Jensen Antenna - Rooftop or Side Mount...
view full answer...
What Type of Cable/Connection/Plug Does the Jensen Antenna - Top or Side Mount - Rubber Mast Use
I spoke to Jensen about the the Jensen Antenna part # 44US01R and they informed me this uses a Motorola style connection.
view full answer...
Recommended Antenna Jack for the Furrion RV Sound bar with USB Charger
The Furrion RV Sound bar w/ USB Charger part # FSB2N25MCBL has a standard size antenna jack port which will work with most antennas such as the Jensen Antenna part # 44US01R.
view full answer...
Static Sound from RV Speakers
If the static you are hearing on your Jensen Stereo part # JWM60A is only when the radio is being played then the issue is most likely with your antenna. I would try adjusting the antenna to see if the static goes away but it not then the antenna may be bad and will need to be replaced. For this, I recommend the Jensen Antenna part # 44US01R which is both a top and side mount. If the static you are hearing is both with the radio and other multimedia inputs such as CD/DVD's then the issue...
view full answer...
Removing the Rubber Mast on Jensen Antenna # 44US01R
The mast of the Jensen Antenna # 44US01R that you referenced can be easily removed by taking out the screw that attaches it to the base (see attached). The mast is actually rubber so I doubt it will do any damage to your cover if you fold it down, plus when you remove the rubber mast half of that ball joint is still attached to the base so it may be better to leave the rubber mast installed.
view full answer...
Replacement AM/FM Antenna For An Airstream Travel Trailer
Hi Cheryl, The antennas are unfortunately not sold separately so if you're just needing a coaxial connection the Jensen Antenna # 44US01R is going to be the right kit for you. You can hang on to extra wiring as a backup incase your current wiring ever goes bad.
view full answer...
Jensen Antenna Rubber Mast Replacement Part
You will need to buy the whole set # 44US01R as we do not sell just a replacement rubber mast.
view full answer...
Do I Need to Use the Included Ground Wire With the Jensen 44US01R
You don't necessarily have to use the included ground wire on the Jensen # 44US01R, but as it was mentioned in the answer that you had looked at, it will help make sure you've got as clear of a signal as possible. With that said, I would think that it's likely that your current cable has a ground wire built into it that is grounded somewhere on the trailer already, so you probably don't need it. If you find that you're having issues with interference once you've installed the new antenna,...
view full answer...
Where to Ground the Jensen Top/Side Mount Antenna Part # 44US01R
I spoke to my Jensen representative about the Jensen Top/Side Mount Antenna part # 44US01R and they informed me that the ground wire coming from the antenna can be attached to either the trailer frame or radio but the trailer frame is the preferred method.
view full answer...
Recommended Exterior Coaxial Cable Inlet For An RV
The antenna ports we currently offer have male connectors on both sides so you would need to get a double-female connector in order to reconnect your antenna # 44US01R when it's needed. We have the following color options: White # SM78VR Gray # SM88VR Black # SM28VR Stainless Steel # SM26FR
view full answer...
Replacement Antenna With 7/8" Ball Joint Width
Hi James, We do have a replacement antenna with a 7/8" ball width, which is the Jensen Antenna - Top or Side Mount - Rubber Mast # 44US01R. This has the ball joint you need so you should be able to do what you're looking to.
view full answer...
Replacement Jensen RV Antenna for 2011 Thor Astoria 40KT
All Jensen AMFM radio antennas have the same thread size so what that means is that for sure the part # 44US01R that you referenced is the correct replacement for your Thor Astoria 40KT.
view full answer...
Is the Whip Portion of the 44US01R Jensen Antenna Assembly Replaceable
Jensen doesn't offer the whip portion of the # 44US01R antenna as a replacement part. You'll need to get the whole # 44US01R assembly in order to replace your missing or damaged whip. I'll link you to a product description video for the # 44US01R Jensen antenna assembly.
view full answer...
Can the Mast On the Jensen Antenna JAN139 Be Replaced With a Longer Option
It is possible to replace the 6" mast that comes with the Jensen Antenna part # JAN139 for a longer option but we do not have any designed for this purpose. If you do need a longer mast then the best option would be to instead use the Jensen Antenna part # 44US01R which can be top or side mounted just like the above but has a 16-1/2" long mast.
view full answer...
Orientation of Plates When Installing Jensen Antenna # 44US01R
The rubber plate of the Jensen Antenna # 44US01R goes on the outside of the RV underneath the mounting flange of the antenna and the plastic plate goes on the interior of the RV. The rubber plate acts as a seal and the plastic plate spreads out the torque of the screws so it can be attached tightly without damaging the install location.
view full answer...
Will the Jensen RV Stereo Part # JWM70A Work with a Batwing Antenna
As long as the batwing antenna on your RV has the standard male antenna jack (see photo) then yes the Jensen RV Stereo part # JWM70A will work. The jack port for the antenna is located on the side of the unit next to the RCA ports. If your batwing does not use the standard male antenna jack and you cannot convert it then it may be time to add a new modern antenna such as the Jensen Antenna part # 44US01R which has both top and side mounts.
view full answer...

< Previous

Next >

Do you have a question about this RV Antenna?

Info for this part was:

Expert Research:

Mike L

Expert Research:

Jameson C

Installed by:

Jeff D

Updated by:

Mary K

Written by:

Amanda M

At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.