Will Biker Bar Fit 2022 Indian Chieftain Limited
Updated 12/15/2025 | Published 11/14/2024
Products Featured in This Question
Question:
Looking at the transport bar set up. I have a 2022 indian chieftain limited, need the bar for the bike with the bracket. Everything is listed for Harley Davison.
asked by: Paul M
Expert Reply:
Hey Paul; B&W hasn't tested the 2022 Indian Chieftain Limited but it may fit the # BWMC2304. To find out if it will fit you will have to take some measurements. A two piece motorcycle tube frame is needed for the Biker Bar to clamp onto. The diameter of each frame tube must be at least 1.125" and no more than 1.5".
Check that there is nothing hanging down below the tube frame, such as a motor, transmission or exhaust. With the rider sitting on the motorcycle, the distance from the side of the frame tubes to the ground must measure between 5" and 6.5".
The distance form the outside edges of each frame tube must be no less than 10" and not more than 14.5". Take this measurement where the Biker Bar will be attached. There must be 1/2" of clearance between the motor, transmission, and primary drive to allow clearance for the Biker Bar clamps.
If you find it won't work you will need a more traditional setup with a wheel chock. You can use the E-Track # e95VR, Wheel Chock # 3481731, Tie-Down Ring # 59131, and Strap #EM59136 to secure your bike.
(click to enlarge)
Continue Researching
- Search Results: military dismount
- Search Results: military discounts
- Search Results: 12k hydraulic jack
- Shop: B&W Biker Bar Motorcycle Tie-Down System Base with Anchor Plates
- Shop: Replacement Clamping Bar for B&W Biker Bar Motorcycle Tie-Down System
- Shop: Replacement Anchor Plates for B&W Biker Bar Motorcycle Tie-Down Systems - Qty 2
- Q&A: Biker Bar For The B&W Motorcycle Tie-Down System for Trailers
- Shop: Fastway ONEstep Wheel Chocks for Tandem-Axle Trailers and RVs - 16" to 24" Long - Qty 2
- Video: Review of Bigfoot Replacement Jack Leg 8K Hydraulic Trailer Jack - BF44FR
- Shop: Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System
- Shop: B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Sportster
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Rack'Em Manufacturing Removable Wheel Chock
- Q&A: Amp Draw for MaxxFan Dome Plus Roof Vent w/ 12V Fan # MA00-03810B
- Q&A: Amperage Draw of The Solera Power Awning Replacement Motor # LC266149
- Q&A: Wire Size Needed For The Furrion 2-In-1 Range Oven
- Video: All About the RV Flooring Adhesive for Vinyl Over Wood, Metal, or Concrete
- Q&A: Recommended Motorcycle Wheel Chock For a Trailer With E-Track Ran Length Wise
- Q&A: Trailer Hitch that Can Fit 2017 Volkswagen e-Golf
- Video: Checking Out the Tow-Rax Removable Wheel Chock w/ Hardware
- Search Results: curt 56434
- Search Results: 11412
- Search Results: hopkins 20099
- Search Results: bd1700100317
- Video: Let’s Check Out the Tow-Rax Removable Wheel Chock w/ Hardware
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Fifth Wheel Towing Made Simple with Daniel
on Motorcycle Tie Downs
Robin H.
12/15/2025
Hey Paul, were you able to take those frame measurements on your Indian Chieftain Limited to see if the Biker Bar would fit? Knowing what you found could help others trying to secure the same bike model.