Best Coachmen Apex Travel Trailer Camper Jacks

One small part was missing from my Ground Control TT. Carol Korren expedited delivery of the missing part and the UPS truck pulled up at the moment I needed the part. Fantastic customer service!

This works great and has been the very best upgrade on any RV/Trailer I have every owned. I will never own another trailer that does not have this.

My Jack arrived DOA. After installing it on my trailer, the Jack didn’t work. The manual crank handle came in handy because I didn’t have time to troubleshoot and repair it at the time. It was just a wire that was no longer connected to the switch but I have to tell you it was extremely disappointing to receive a brand new item that didn’t work. If it had worked out of the box, I’d give it a five star review. You should consider soldering and heat shrinking the wires to the switches or making the wires longer so they aren’t banjo string tight and putting the lug at a strange angle.

This particular jack fit my 2001 Horse trailer perfectly. I had it installed in about 2 hours due to clearances on this particular type of Tonge design. Otherwise with a couple box end wrenches and a hydraulic bottle jack this jack could be installed in 30 minutes. It appears to be a very good product for the money. Also, it has plenty of lift capacity. 8000 pounds which is perfect for my trailer.

Replacement for bent camper stabilizer jacks, these work great.

Jayco camper came with stabilizing jacks in the rear but none in the front. After wife complained that my walking around in the camper in the morning made the bed feel like a water bed I installed these jacks. They work perfect, easy and fast to deploy and camper is now solid when parked.

The powerhead is very large and extends forward, which has caused it to impact upon two different vehicles when backing the trailer. The power function is now useless, and I am using the manual crank to raise and lower the jack.

Sturdy jack, easy to install. We installed it facing to the driver's side so we can still put our tailgate down. Very powerful jack, only drawback is it is very slow.

This Bulldog replaced an Atwood jack on our Lance 1575. The Bulldog is quiet, but there is a fair amount of play between the inner and outer tubes. It feels unstable even when fully retracted. This wasn't the case with my old Atwood jack. If I had known this, I would have gone with another brand. I bought the Bulldog based on the reviews and the warranty, so I was surprised that there is so much wobble in it.

Installation was quick and easy per the instructions and eTrailer video. One of the few times I've had something "bolt right in/on" LOL. It has worked flawlessly in the time that I've been using it. The only drawback, and it is a small issue, is that it is easy in the heat of battle to bump the light switch ON and not see it in the daylight. One just needs to be careful or use a bit of tape to secure light switch OFF until needed. Another great product from etailer.

Works great as a stabilizer. I have a 38' trailer and I use screw jacks to level the trailer. Once the trailer is level I lower the stabilizer jacks to eliminate any movement. With this combination the trailer does not move one bit.

There's not a lot to say. The first Stabilizer carton was damaged to the point the carrier couldn't even find the Stabilizer. etrailer.com was very cooperative & sent a second unit out right away. Although the second shipment packaging was damaged all parts were there and undamaged. I installed the unit and it is so so much better, quieter and faster than the old unit. I highly recommend both Lippert and etrailer.com

I should have got one years ago. I only use it when it's connected to the truck with the engine running. This I believe gives me full power. It has enough power to raise the trailer when connected to the truck to get the anti sway bars attached. Sure beats all that hand cranking.

I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."

Very happy with this powered jack. I will definitely be buying a second one for my other trailer. Installation was very easy and straight forward.

Easy install, able to mount sideways so I can open my tailgate now.

I purchased this jack to replace my tired 10 year old camper jack . I ordered it at 10:00 AM Monday and as promised by Ian it was at my doorstep on Friday just in time for my weekend getaway . Installation was a breeze . I gave the product a 4 out of 5 for a few reasons . First , I was not able to see the manufacturer of the jack before receiving it . Which made name brand comparison pricing difficult . However I feel pricing was on target . Second , I feel that the jack should come with a battery terminal end connector and new mounting bolts with the hardware that was included . This didn’t pose any difficulty to me as I had hardware at hand but for some it will mean a trip or two to the hardware store . Third , once installed , at least with my truck and trailer , unless the truck and trailer are perfectly aligned and level the jack motor gets in the way of opening the tail gate . On first use I noticed it was much slower than my original but the strength made up for it . This jack had no difficulty or hesitation lifting my truck and trailer for load distribution and anti sway bar installation . I would recommend etrailer and this product . Time will be the final test of its durability .

Ok.... the customer service from ETRAILER totally saved the review! These guys are incredibly awesome. I ordered 2 of the jacks. The first came with a broken housing cover , the light had beed disloged, and the up down switch was wired backwards. (Up would put the jack down and down would put the jack up) Solution? Glad you asked! I contacted ram about the cover.... waiting! The light was easy to correct, just had to slide it back into the slit that holds it. Switch, well.... if-your2 not comfortable with wiring, I recommend not even attempt to rewire. I just popped it out of the cover, twisted 1/2 turn, popped it back in. Total time to correct.... 8-10 minutes. Total time to install, 15 minutes. Total job less than 30 minutes. Would I recommend this jack... YES. Despite a shipping issue to crack the housing ... its easy to install, price right, powerful. I dont have to hand crank. Simple correction to the switch. And they could use some r&d improvment on the light... but excellent jack! It does what i meeded it to at an affordable price!

if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.

The jacks themselves have worked great, they keep the trailer level and solid during our concession events. I just had them mounted to the trailer so I don't have to put them in and out at each event. The jack handles leave a bit to be desired so I use a 20v drill w/ a 3/4" socket to run them up and down.

Installed jack on trailer, tested with a battery. Works great, it will lift my cargo trailer high enough for my 3/4 ton Ram. In the past have had to carry 3 blocks for the screw jack, now only a small one just to keep the steel jack pad off the cement or ground. Have not wired the new jack yet, we still have winter here in ND and will not use it until the end of April. The jack, I believe, will work fine. I forgot to order a cover for it when I ordered the jack, just did that this morning. Thank you etrailer.

The jack works great. I didn’t have any problems with the installation. My only issue is that the holes are 90° off for my Fastway jack foot which goes up automatically. I’m debating whether to leave the jack 90° off or drill new holes in the jack.

Great product. works just fine. The problem I had was matching the mounting plate under my trailer. Apparently not a standard so I had to take it to a trailer manufacturer to make it fit.

They went on a custom made trailer build that’s not yet in service. Seem to function as advertised.

Fast Shipping and delivery, worked great as replacements for my old worn out stabilizers

Quick shipping. I will be ordering more parts as I need them for our RV.

Got my product when promises. exactly what I ordered ( and on sale too) Alex was great. I WILL BUY HERE AGAIN

Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.

The product works as designed. Easy to install and I have used it approximately 20 times in the last year. The storage for the 7 pin connector and safety chains are a great option. Keeps things nice and tidy when unhooked. I highly recommend this Jack.

Perfect fit and operates very quietly and with abundant power for my 27 foot Lance travel trailer. The Jack-It Lippert bike rack mount fits perfectly over it, and the manual emergency jack crank fits within the tube of the Jack-it if the need arises. Also, the handy ring for stowing the trailer chains and receptacle for stowing the 7-way connector is a nice feature. Very happy with my purchase, and etrailer is fantastic, as usual!

These are great jacks. I have 3 of them. The only reason I replace one was because I bent it. Let's not go there.

This jack was the perfect solution for my application. I have a new enclosed trailer that came with a manual crank and only a tiny battery to run the lights. I did not want the expense of having to buy and cable up a larger battery to just support the tongue jack. Took me 5 minutes to install this new jack using the three bolts that were already on my OEM jack. Now I just back up my truck, plug in the 7-way, and I'm able to move the tongue up and down as needed. Great!

Perfect! My weld for rear bumper was in the way of the bracket, so I just swapped 1 bracket each side from the old jacks, jacks were same size but rated lighter weight. Thanks for quick delivery! Always like the tutorials and pictures.

The box was a bit beat up when it arrived, but hopefully everything is intact.

Very happy with the quality of this stabilizer jack!! I currently only have the jack installed on one end of our toy hauler and you can feel the difference in how stable the camper is on one end compared to the other end that still has the scissor type jacks. I will definitely be purchasing a second one!!

This product is awesome and has made a substantial difference in the stability of our camper! We have a 32' travel trailer and the factory jacks are sad and could feel every movement of the kids. This has taken away 90% of the movement that we were having before. If you are not handy plan on having someone install this for you. It's not hard to do but if you don't have some tools for the job you will struggle. It took about 4 hours total to install.

It installed very easy. For a 2500lbs jack, it seems a little light weight. It does lift the trailer but seems kinda wobbly because the post size is so small. Other than that it works as advertised. Thank you for getting it to me so fast.

It seems like a good quality jack, but it's a real product failing that a dedicated ground wire is not included in the product along with its dedicated 12V wire. Our Featherlite horse trailer has no battery, so we bought a 7-pin plug and used it to connect the 12V wire to the truck's receptacle. We asked before buying the jack if it could be wired this way and were told yes (or we wouldn't have bought this jack). But when using the jack this way, following the instructions and grounding the jack at its mounting bolts is a problem because as soon as the trailer's receiver loses contact with the ball of the towing truck's hitch, ground is lost and the jack stops working. To prevent this, the factory needs to supply a dedicated ground wire along with the dedicated 12V wire, or better yet a prewired 7-pin plug just like the "plug-and-play" electric trailer jacks Walmart sells for considerably less money. Luckily ETrailer's customer service is great and both Will and Aaron were very helpful, so we were able to sort it out. But a prewired 7-pin plug would have made for a much better experience.