# 1
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
It works great! Easy, quick, you know. One needs to screw in the hitch bolt, for some reason, before latching it. Other than that, it makes going bike riding way easier.
# 2
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
I bought this bike rack back in April but wanted to make sure I used it to give the best review. First I want to say I did a lot of research on bike racks and found this one to be the best one to fit my needs. The best price I found was on etrailer.com, at the time it was When I called the customer service to place my order, I spoke to Dan. He was very pleasant on the phone and took the time and listened to what I needed and understood my concerns. I ordered the bike rack and also ordered the Thule Snug Tite Hitch Lock and Anti-Rattle Device and the Thule Cable Lock w/ One Key System Lock. Dan suggested I also get the Thule Bike Adapter Bar, which I never even thought of getting. Delivery was in about two business days, which was really fast and at the time of order they were running a special free delivery over $99. When I went to put it together I noticed I was missing the flat cap screw M6 x 16mm, part number #853-5787-02. I emailed Dan and within 24 hours received an email that the part was sent out and also in the email their was a link to track the order. After I received the part I did notice that the flat cap screw was actually in the 2 inch adaptor sleeve. The instructions were very easy to read, and it took me about 20 minutes to put together. I did have an issue when I positioned the stinger into the cradle, with the 8mm locking nut, it was not staying tight and when I took it off I noticed the threads inside were gone, so I ended up going out to Lowes and buying a new one and its holds perfectly fine. I also had a question about that part because it is not a locking part and was worried someone would try to steal the rack. I contacted etrailer.com to find if they make a locking device for this and they said no but I can contact Thule to double check, I'm still waiting for an answer back from Thule. The weather finally broke and we installed the rack onto my hitch, tightened it and it doesn't rattle. When I finally used the rack and put my bike on, it did sway a little but at 50 mph I was very happy with it. The trailer comes out just enough away from my car that I do not have to fold completely out and I can open my trunk with no issues. I am very happy with my purchase and had a great customer experience with Dan. Would highly recommend ordering from them to anyone.
# 3
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 4
Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
etrailer: prompt delivery, fair price! Rack: It does fit my (2) Gazelle T10 eBikes. 1) I found I had to adjust every setting to get bikes to fit. Until you learn there are many adjustments, it does not seem like the center/vertical clamps will reach both seat posts. 2) The ramp is barely usable; my wheels are max it will fit and you must have at least 12ft of clearance on each side of car to get bike lined up with ramp. 3) My bikes have a "walk" feature, this is not usable as its too awkward to hold the walk button down and move around the rack. I found its easier to abandon the ramp and load front then rear wheel. I will rig up a wheel stop, on ends of each wheel holder so bike will not roll off while I strap it in. 4) Rack did NOT come with a lock for hitch pin; this is very disappointing as they say in manual this is an optional item. Every rack I have seen at least has a clip that would otherwise hold the hitch pin in if somehow the bolt loosened up. 5) The rack weight is the lightest I have found. 6) You must load the first bike (closest to car) from car passenger side. This will avoid you bike pedals hitting the vertical bar. That means you must load the 2nd bike manually as there is no way to get the pedals past the vertical bar. I will get used to this, I hope. 7) The rack is a few inches above the receiver (part that goes into hitch) so if you have a low hitch this might be an issue with ground clearance. With both bikes mounted up, it seems very stable and hopefully will be secure in travel.
This is a great product and works beautifully! The only issue was some sloppily made plastic turn knobs that were cross threaded on arrival. However, Yakima immediately shipped out replacements. It carries two large E bikes easily. They fasten solidly and are easy to load and unload!
# 5
Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This bike rack works great for our 2 Lectric 2.0 e-bikes. We mount it on our 2019 Honda Ridgeline. It folds up nicely when it’s on the truck and we are using our bikes. The locking mechanisms work well also. I contacted support for a smaller hook arm to clamp B over the bike frame. They knew exactly what I needed and shipped it - no problem.
I've been using this bike rack alongside a trailer hitch I got here for my small car (chevy bolt ev) and it was exactly what I was looking to get to haul around my fat tire mountain bike bike. Sometimes I throw two bikes on there (either an e-bike, slightly heavier at 60 lbs, or a 2nd mountain bike) and it's perfect.
# 6
Hollywood Racks Destination Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
Used it twice so far, it meets my expectations based on other reviews. It's easy to load the bikes (8 minutes or so for 4 bikes) and to move up or down. Glad I bought this "lighter" platform rack rather than the swagman because while it's not hard to get into the hitch, neither is it "light". Anything heavier would definitely be a pain. Hopefully straps etc are durable over the long haul. No problem getting 2 adult and 2 kids bikes on. Glad I went with a platform rack over a bar. My sister has the bar rack and says it's impossible to get 4 bikes on.
Ok so I I was going to buy a safari rack which ended up being about $100 more once you tacked on taxes and shipping from another website. This was on sale and had really good reviews. I bought this and have used it long enough to leave an honest review. It’s a really good rack, quality built, and If anything should break on the rack etrailer has all the replacement parts for very cheap prices. I have used this racks for shuttle duties and held 4 big enduros bikes several times. You don’t need to use the extra red straps sent with the rack for the bikes to be very secure. As someone stated before in the reviews long wheelbase bikes like size L or XL frame enduro or DH bikes might only be able to strap one wheel and frame attachment (the one wheel will be too long to get a good strap on), but all you need to do is drill a hole and move the clamp outboard about 2” and you’ll be good as gold. This rack is awesome and was a heck of a deal. Would recommend and buy again if I ever needed 2 racks? Also not to mention (not that I really care), but the rack was packaged really nice and didn’t come all damaged from shipping, it was really nicely formed foam that was glued in place and not just some hack job some guy tossed in a box. 10/10 !
# 7
Thule T2 Pro XTR Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
T2 Pro bike rack was delivered in a very timely manner. The rack was as described, extremely easy to assemble and is super user friendly! Exactly what I was looking for so my wife can use it by herself. Thanks
Great product, great company to do business with. etrailer is the best. Friendly, helpful and they made sure the bike rack was shipped immediately and it was delivered on time.
# 8
Softride Shuttle Pad Tailgate Pad for Full-Size Trucks - Up to 6 Bikes - 61" Wide
The fit for a 2014 Ram was spot on, no issue with the wide style tailgate top and the access flap for the tailgate handle lined up perfectly. Material is durable and easy to clean, the only thing holding it from a 5 stars is if it had the padded dividers on top to keep the bikes separated. But for the price, the fit and finish was exceptional, great value !!!
The product review/installation video helped me make my selection. I selected the full size pad for 2001 Silverado 1500. Installs easily, fits nicely, flap in pad is positioned for easy access to tailgate latch.
# 9
Rhino-Rack Bike Rack for 2 Bikes - 2" Hitches - Tilting
I purchased this bike rack a year ago and I use it A LOT. I had to buy and install a stabilizer because without it, the unit would sway back and forth even without a bike on it (very noisy). This makes removal more cumbersome but since I keep the hitch on year round it doesn't matter to me. The tilting function is fabulous allowing easy use of my RAV4 hatchback. I can even tilt it down with a bike on it. I got the 2 bike hitch. Plenty of room for two bikes to fit without rubbing. Lastly, the hitch has a sizable through-hole on the bottom to thread a good sized cable so I can lock my bike up. Sturdy. I highly recommend.
The unit ‘s simplicity is a real plus. It takes less than 3 minutes to put the rack on the vehicle. It is well built and very durable and has a nice feature that allows you to open the rear hatch for SUV owners without removing the rack.
# 10
RockyMounts BackStage Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
We love our RockyMounts BackStage Bike Rack. The fact that it can hold our two e-bikes and swings out for rear door access makes it perfect for vanlife. Service and communication from etrailer is outstanading!
etrailer.com asked me for a review about 1 week after it arrived. A better review would be in about 6-12 months after delivery to allow me time to use and experience the rack. Disclosure: my review is just for the assembly and install. Assembly is not easy. I needed to go to the internet and look at photos. The instructions lack detail. So only 4 stars for assembly instructions. It seems like a good design. The included locks seem cheap - like why bother including. The hitch pin design seems to tighten down the rack so there should be minimal rattle and movement. The rack sits up relatively high, so it would be safer to lift heavier e-bikes with two people or use some type of field engineered ramp. Wish it was made in the US and I wish the country of original was fully disclosed in the etrailer.com description. Perhaps it is disclosed but I learned it was from china after it was delivered.
# 11
Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On
The Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On, is just what I was looking for to be able to build a bike rack for carrying one of my bikes on my motorcycle. It was easy to mount and it holds my bike in place while riding on bumpy dirt roads, city streets, highways and even when I hit some twisty country roads. It's really easy to load and unload my bike when I get to where I want to ride. I use a velcro strap around the quick-release and the fork arm as an added safety as well as a couple tie-downs from my bike handlebars to my motorcycle passenger pegs to help distribute the weight on my rack. If you want to build your own DIY bike rack I totally recommend the Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On.
Love this product! I built a great bike carrying system for my F-150 using two of these fork clamps. They are easy to install and extremely well made. No more tangled bikes and lots more room in the bed for other stuff! Best way to go for a nice bike rack system. Thanks, Phil T.
# 12
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I bought this bike rack because I didn't want to have to remove my bed cover every time I wanted to take our bikes on a trip. This rack works perfect because I can roll up my cover and this thing just clamps across the bed. Taking the front tire on and off is kind of time consuming but when I travel with my brother who has a hitch mount rack, it takes him just as long to unload his bike as it takes me to unload. The wheel mounts tighten easily and the bikes appear secure during long drives, so I don't worry about them coming loose. Of course, you'll want to wrap a bike chain around the bike and rack if you plan to leave them out to make sure no one can steal the bike (although it would be missing a wheel)
Referring to special mounting instructions if you have a bed liner: (line #3). I do not have a bed liner, but I do have a molded plastic cap on my bed rails ('04 Ford F350). The first install over the plastic cap the locking pin or pin as called out in line #3 was nowhere near making contact with the metal lip of the metal bed under the plastic. What I did next on the second and final install was remove/cut away the plastic on the inside of the bed rail to allow the vertical portion of the "L" mounting bracket (Fig 4) to contact the metal bed. The locking pin is now at a position almost where it would protrude under the metal bed lip if I would remove the rest of the plastic under the horizontal portion of the "L" mounting bracket, I did not do that. After cutting a notch in the metal rail to accept the pin, the pin barely flushes out to secure the rack. A 1/4" longer pin would take care of this problem. One other thing that was not addressed in the install instructions was if you have a full size pick-up bed you are likely to attach the passenger side fork mount (Fig 2) to the right of the extension tube locking mechanism. The extension tube is a smaller diameter, so you will have resize the fork tube clamp (Fig 1) for the smaller tube. I can't explain how to do it other than it's a Chinese puzzle.
# 13
RockyMounts MonoRail Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
At age 75, I have purchased many bike racks over the years…..this one has no equal in loading and unloading…
This rack is really, good. The only thing i add to make it better is small strap that holds the front wheel to the front wheel bracket. I never had a problem with it, but i like to make sure it is secure. It is a solid bike rack and worth every penny. I would buy this over the Kuat version any day.
# 14
Yakima HoldUp Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Works well for transporting two 29" wheeled mountain bikes. However, after one year it's starting to rust in several areas (see attached photos), and the front wheel arms are becoming increasingly difficult to raise and lower. Finally the locking cable is extremely rusty as you can see in the attached photo. I'm not sure how durable this rack will be long term.
We have had this bike rack for one year and use it every week-end. My wife has a Trek e-bike (52 lbs) and I have a regular Trek hybrid (23 lbs). The rack is very sturdy and I have no issues driving at highway speeds, there is no movement of the bikes. Very easy to load and unload.
# 15
Kuat NV 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Metallic Black
EVERY BRAND HAS ITS PROS AND CONS. THE PROS ON THIS RACK IS THE HIGH QUALITY OF MATERIALS AND CONSTRUCTION AND THE INNOVATIVE FEATURES. THE RACK IS EASY TO USE AND EASY TO INSTALL. I ESPECIALLY LIKE THE INTEGRATED BIKE STAND. IT IS EASY TO USE, UNOBTRUSIVE, AND COMES IN VERY HANDY WHEN YOU WANT TO MAKE A TWEEK ON YOUR BIKE WHILE AT THE TRAIL HEAD OR IN THE PARKING LOT. I KNOW THERE MUST BE A NEGATIVE TO THIS RACK, BUT AFTER A YEAR OF USE I HAVEN’T FOUND IT YET. IT IS A BIT PRICEY, AND IF YOU DON’T CARE ABOUT DURABILITY, QUALITY OF CONSTRUCTION, OR ADDED FEATURES, THEN A LESS EXPENSIVE BRAND MAY WORK FOR YOU AND YOU WILL SAVE A FEW BUCKS. ALSO, IT IS A BIT HEAVIER THAN SOME OTHER RACKS, BUT I AM IN MY 70’S AND I CAN HANDLE IT FINE.
Fantastic bike rack!! After getting fed up with loading my bike up repeatedly in the back of my 2003 GMC Sierra pickup (with a hard top cover) I decided to purchase this kuat rack. I wish I would’ve sooner. Assembly was easy and straight forward however I would use a magnetic parts bowl if I had it to do over. Kuat doesn’t included any extra nuts so I had to contact them to get another after I dropped and lost one (they were very polite and shipped one right away.) As far as function goes this rack is really easy to use. Just slide it into the receiver and put the lock pin it. Just like in the video you then tighten the knob at the back to secure the hitch so there is no movement. Load your bikes up and secure them and you’re ready to go. I did utilize the retractable cable locks after my ride when stopping to eat and they are very easy to use. No worries at all about a stolen bike. And the tilting feature is great too. It does allows you to access your truck bed with the tailgate down just as in the video. As an added bonus this rack fits perfect in my standard size truck bed even with the hard top cover closed (my truck is too long to fit in the garage with the rack folded up installed in the hitch.) Michael H. was outstanding providing schematic drawings with the dimensions so I would know this before my purchase (they’re on the Q&A page.) The free shipping was very fast so that made the purchase even better. I will definitely be a repeat customer as eTrailer is the one of the best companies out there with great customer service and timely communication. Great job!!
# 16
Yakima HighRoad Roof Bike Rack - Wheel Mount - Clamp On
1. One star ding for price. Fairly expensive for a single bike, especially after adding a lock core. 2. The rack works exceptionally well and I'm not disappointed with the purchase. Installation is fairly simple. It does take a bit of fiddling to get the tension down on the rack clamps (connecting it to car) but it is a simple affair, and I'm able to move it between an aero rack and a round rack with out adjusting the tension. The sliding tray in the rear is a bit sticky, so if you carry bikes of different wheelbases, you may need to add some lubrication to the tract. Front wheel locks into place (I've used 700x25 and 29x2.3) simply, and the clutch in the tension wheel is a nice addition. It would be nice if there was a quick release button (like in times past) but it spins fairly quickly to unload. The locking whip is a nice addition. I have been able to rout it over the chainstay on both bikes. However, it is too short to route around chainstay and wheel. I'd prefer to include my rear wheel inside the lock. Overall, I'm very happy with the product.
I bought two of these, they work great, good the bikes very solid and I'm confident using them over hundreds of miles. etrailer.com is my go-to for tracks and accessories
# 17
Inno Velo Gripper Bike Rack for Truck Beds - Clamp On
1 year ago, ordered 2 pair Inno Velo clamp on bike rakes for pickup. One pair received damaged/used. eTrailer credited 50%. Rated average for 2 reasons. First, I couldn't get them to work securely with my tonneau cover without modifications (plastic spacer blocks to clear tonneau rail) and I can't close the tonneau cover over them when not transporting bikes. Second, while not recommended for ebikes, they kinda worked but are not strong enough for the weight of the bikes especially when needing to extend to full length. I like the idea but just doesn't meet my needs. Otherwise, they should work just fine under different applications. Best use is to install and left installed. In my circumstance, removal & reinstallation was a pain.
Using the Grippers for carrying 2 ebikes, weighing 55 & 75 lbs. I know this is above the rated bike weights but so far they have performed well. My short bed keeps the 75# bike pretty well locked in front to back so that may help.
# 18
Kuat NV 2.0 Base Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Matte Black
I've taken this rack all over New England on the front of my Dodge Ram 3500 pick up truck with a truck camper. I had no idea it was possible to love a bike rack so much. After one drive I didn't ever worry about it again. So nice that it locks up when I am camping or taking a quick stop for food on the road. So glad I bought it from etrailer. They totally help me pick the perfect rack for my challenging set up.
Still very new, but what an awesome bike rack! Assembly was a snap and the rack is rock-solid when you secure it to the hitch receiver. etrailer was amazing too - excellent communication, price and fast, free delivery. Overall I am extremely happy with the rack and service!
Thule Truck Bed Bike Racks Review - 2015 Ford F-350 Super Duty
Today on our 2015 Ford F-350, we'll be doing a test fit of the Tooley Instigator truck bed single bike rack. Part number TH501. We already have the bike on the rack. I'm just going to show you a few features of it. The main feature I want to show you is the frame hook its self; how it's engaged and how you disengage it. It's a button down here, black button, press on that. Just bringing it out just a little but and you can bring it down towards you.
Inno Truck Bed Bike Racks Review - 2015 Ford F-350 Super Duty
Today on our 2015 Ford F-350, we'll be doing a test fit of the Inno Velo Gripper Bike Rack. Part number is INRT201. Now, we already have a bike on our rack. We'd just like to show you a few features of it. Now, how we have our bike connected, we have two straps. One is going around our forks here, and the other one is going around our side row here.
Thule Truck Bed Bike Racks Review - 2015 Ford F-350 Super Duty th824
Today on our 2015 Ford F-350, we'll be doing a test fit of the Thule Gate Mate Tailgate Pad and Bike Rack. Part number is TH824. Now, we have it right here. We're going to show you how we install it. This is 62 inches long. It's going to be good for your extra long tailgates. First thing first, we want to do, we're going to go ahead and just show you a couple features here, now.
What our customers are saying:
"I think this website is very useful for hitches and every other stuff as bike rack and wires harness for vehicle. I would recommended this site to everyone I know."