To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If you like your vehicle to keep a clean, factory look when it’s not being towed, this setup does just that. The brackets mount on the frame and sit farther back than standard base plates, so when the drawbars are removed the remaining hardware is virtually invisible. There’s no bulky quick-disconnect crossbar hanging out front—just a smooth, low-profile finish that stays protected from scrapes and scuffs inside the grille.
Getting hooked up doesn’t have to be a hassle. The removable drawbars slide in, twist to lock, and click firmly in place—no tools or extra hardware needed. When it’s time to unhook, just pull the built-in release ring, twist, and slide them out. It’s a secure, reliable system that saves time at camp or on the road.
Flat towing puts plenty of force on your setup, so this kit is built from computer-cut, all-steel components for exceptional strength. The black powder coat finish adds corrosion resistance for long-term durability through road grime and weather. It’s sturdy hardware designed for thousands of towing miles without giving up integrity.
This base plate kit bolts directly to your vehicle’s frame for a solid connection. There’s no welding involved—just follow the included instructions and use the supplied mounting hardware. The custom design ensures everything lines up where it should for a secure fit that’s ready to tow.
The direct-connect brackets are made specifically for Roadmaster motor-home-mounted tow bars that slide into a trailer hitch, such as the Nighthawk, Sterling, Blackhawk, Blackhawk 2, Falcon, or Falcon 2. They eliminate the need for a hitch ball or separate crossbar so you can hook up directly and get moving without extra parts in the mix.
Ratings & Reviews
The folks at etrailer are fantastic. I didn't know everything I needed to tow my car behind our RV... but they did! Everything I needed was in the boxes and the videos made it all come together. Thank you to everyone at etrailer!
It mounted up just as the instructions said it would. From previous research I was not surprised when some of the mounting did not align perfectly. Had to use a dremel tool to make it work. The product looks very sturdy from its design. I’m happy with it and look forward to RV traveling.
Good product. If you are reasonably handy and have some tools, you can install this yourself in a few hours. I'm a mechanic, it took me a little over 2 hours to install on my own toad. The fit is good, there are 4 holes you have to drill, otherwise it is plug and play. When you insert and twist lock the tow bar mounts into their sockets they feel a little sloppy but they are secure, and i never noticed any rattle when towing. Overall i give it a 4 out of 5 for easy install and clean look after install. Pic included of installed base plate.
This was a bit of a challenge to install on a 2026 Chevrolet Colorado Z71. One item to be aware of, as you take off the front Facia of the truck for the install, there are two Facia "brakets" that attach to the front fenders that seem like they are use once plastic snaps. Three of the 4 snaps broke off on both sides when I removed the facia. These are about $35 a piece from Chevy and prevent you from making this a 1 day job. Additionally, there are 2 7mm screws/bolts that connect one of the coolers to the back of the bumper support and these are a real problem to get back in - over an hour of time and every 1/4" tool in my arsenal was needed to find a way to get these started. Finally, one of the Connecting Plates (Passenger side) needed to holes to be elongated to enable all the bolts to be started. Finally - you need to put the Brakaway bracket on the driver side, to have enough cable to reach you brake system. Probably have 4 hours in the disassembly and installation of the Direct-Connect Plate. Now waiting a couple days for the plastic brackets from Chevy to complete the install. Good Luck!!
Very fast shipping, and the install was easy. Great product
Awesome instructions! Install was fairly easy. Product is very high quality and solid construction. Thank you E Trailer!
I installed this base plate on a 2018 Miata RF. I think I recall something about it taking 3.5 hours and my initial estimate was 3.5 days. It actually took a bit longer than that, but I was not pushing myself and did not have the luxury of having the vehicle on a lift but had it up on two ramps for the front wheels.
The order came pretty quickly, probably about 4 or 5 days between the time I placed it and UPS delivered it. The parts were well packaged and it came with a printed set of instructions. I had watched the video install on another Miata and if it weren't for that I'm not sure I would have tried it. I'm not a pro mechanic by any means but have worked on my own vehicles now for over 40 years. And I'm not a spring chicken either, so all the up and down working on the car can tire me fairly quickly. But if you are not in a rush and go carefully it can be done.
It took a day to do most of the disassembly. I removed both headlights and the intake tube on the passenger side. That tube came out much easier then it went back in.
The next day I got the baseplate mounted which helped to start visualizing how it all would work. All of the holes for the 6mm bolts did not quite line up with the holes in the frame. I had to file one sides worth for a bit of extra clearance. From my experience on this install you really want to leave all the bolt on the loose side till you get everything situated.
A couple of days off for rain and the then I got to work on the bracing. Initially I though I didnt need to cut the top lip of the frame but I decided to go ahead and do it anyway since that part didnt seem to sit flat when bolted from the back end. I'm still not sure its really necessary as the hump clears the metal lip without cutting it.
I also ordered a 14" long 1/2" drill bit to cut the holes in the frame. It was a Bosch bit, wasnt very expensive and it went through the metal like the proverbial hot knife. I managed to get all the big bolts installed in a day with a great sense of satisfaction.
The next day I torqued down all the bolts and the mount felt very solid. They stress that you need to install all the bolts, but honestly I can't see the 6mm bolts doing much compared to the half inch bolts that do most or all of the work. But I put them in and tightened them all the same.
A couple of days spent to install the tail light wiring and then I got back on to putting the front clip back on. My car must have had an aftermarket grill since it did not match the pictures or the video. I tried to position it carefully to see where the parts that were going to stick out would be so I didnt cut out more than I needed to. So there was a good amount of back and forth, cut and fit. In the end I had to make some extra cuts for clearance for the safety cable tabs as well as the mount for the 6 wire connector. Until I made the extra cuts the lower part of the front clip would not seat correctly. Getting the clip in the right position so it fits under the lights also takes some finagling.
Figuring out where all the bolts go back in can be interesting. Take pictures where you can. Dont be too aggressive when working with plastic parts. Overall I'm satisfied with the install, but I have yet to try and hook it up to tow.
Easy to install needed to replace some fasteners as they broke removing front grill was able to get them from Amazon cheap
Easy installation! Etrailer videos are very informative and helpful! Always great to have a helper too!
This Road Master Direct connect base plate works perfectly for a 2020 ford transit cargo 250! Awesome service from etrailer as usual! The finished product can barely be seen through the front fascia!
It was shipped promply. I installed it myself using the included step by step instructions and videos from etrailer. It all went well (though I had to come back and reconnect the sensor plug- my bad).
I tow a Jeep Grand Cherokee Trailhawk and this base plate is nearly invisible when not towing. Works well.
I bought and installed this tow plate one year ago on my 2013 Jeep Wrangler. I bought this particular plate due to the jeep having a Barricade off-road bumper. This plate attaches a bit lower than other plates and prevented having to modify the bumper. Installation was easy involving only hand tools. The plate comes with all needed bolts and attachments. I have towed this Jeep several thousand miles behind my RV with absolutely no issues. As an aside, I use a Roadmaster Night Hawk tow bar which is also an excellent product. Both are expensive, but I believe cheaping-out on safety is no a good idea. I highly recommend this product.
This works perfect with my Roadmaster tow bar. It was a little difficult to install since I had to remove the front end of the Trailblazer, but with the good directions that came with it and some you tube videos made the installation easier.
Had these installed at Lester’s Automotive in Boerne,Texas…First class service all the way. Paul and his crew worked through lunch for over 4 hours to install these on our 2026 Ford Ranger. Also ran the wire and hooked up my auxiliary tow lights. The price for this was very reasonable and would highly recommend them for all r.v. needs even if not real close to the Boerne area. R.V park within reasonable distance if needed.
Etrailer comes through again! This was a great savings as a used kit, but it was even better than the description online. I have installed (4) baseplates on and etrailer.com has given me great videos to watch and good instructions to follow. Couldn't be more pleased with the quality, service and delivery times.
Just what I wanted.
These work great!
My husband was able to install this very easily. We ground tow our Chevy traverse behind our class A motorhome.
Best plates on the market, install was good. Etrailer is the only place to buy!
The Roadmaster EZ5 base plate works as advertised. Installation was not complicated and instructions were good.
Although I haven't installed this item as yet, I want to comment on the service I received from the staff at etrailer. They were without a doubt, the most knowledgeable people I have ever dealt with, not only did they know this product, but they were well versed in its application, and how 2 different parts compared & what was unique to each one. They helped me make my decision, the part was ordered and shipped out the same day. That's the way to get customers coming back. And then on top of that the shipping was free. Wow ! Thank you etrailer, i'll be calling you again.
Very easy to install and as usual, always a pleasure to deal with Etrailer. Their videos are a fantastic plus. They explain everything in great detail. I have purchased vehicle hitches, wiring systems, trailer wiring kits and a braking system for my towed vehicle. I always go to Etrailer first as I am confident in their pricing and educational info.
Frank A.
10/28/2017
Couldnt be better. The same as when I installed it
Base plate fit perfectly, instructions and videos were great. Required some trimming of front grill, blends in very well.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
James M.
7/10/2019
With the included instructions, installation was easy. Now it takes me only a few minutes to totally hook up my dingy, & Im not filthy dirty, like i used to be, with the car dolly. I also find it easier to tow, since the vehicle profile isnt as wide.