See what our Experts say about this CURT Trailer Hitch Ball Mount

• Comparing the Receiver to Bumper Clearance for Trailer Hitch Receivers for a 2015 Toyota Corolla
  I will go ahead and give you the measurement for the 2 hitches that are a confirmed fit for your 2015 Toyota Corolla. From the center of the hitch pin hole to the outermost edge of your bumper will be as follows: Curt # C11265 - 3 inches Draw-Tite # 24913 - 2 inches Since they all have 1-1/4 inch receivers it really just depends on what you are planning to use the hitch for when it comes to deciding which is best. They all have the same weight capacities and Class I restrictions. (see...
  view full answer...
• Ball Mount Recommendation for Curt Hitch for 2008 BMW 335xi
  With Class I hitches like what is available for your 2008 BMW 335xi, part # C11033 you have to go with the recommended ball mount otherwise the warranty of the hitch is no longer valid. So you have to use the part # C45521 which is what Curt recommends. It has a 2-5/8 inch drop and 3-1/4 inch rise.
  view full answer...
• Recommended Euro-Style Ball Mount for a 2015 Nissan Altima with Curt Class I Trailer Hitch
  The recommended 2 inch Euro style ball mount for Curt trailer hitch # C11352 on a 2015 Nissan Altima is # C45572. I went out to the warehouse and pulled one to take some measurements. From the center of the pin hole to the part of the shank where it starts to bend up is 3 inches. This will work because the rear bumper on the Altima tapers upward above the hitch receiver. At 6-1/2 inches out from the center of the hitch pin hole, where the shank starts to bend straight up, it is at a height...
  view full answer...
  
• Picture of Curt Trailer Hitch Installed on a Cadillac CTS Coupe
  Curt has a nice picture of trailer hitch # C11196 installed on a Cadillac CTS coupe. I have include it for you here. The hitch receiver and cross tube are visible beneath the rear fascia of the vehicle. If you plan on doing any towing with the hitch then the correct ball mount to use is # C45571 for a 1-7/8 inch ball or # C45572 for a 2 inch ball. For trailer wiring you can use # C56044. I have linked the instructions for the wiring as well. If you are using the hitch for a bike rack...
  view full answer...
  
• How to Install the Curt Trailer Hitch Receiver on a 2013 BMW 128i
  The only hitch receiver we have confirmed to fit your 2013 BMW 128i is the Curt Trailer Hitch Receiver part # C11184. Unfortunately, we have not had a chance to install this hitch on a 2013 BMW 128i yet. However, the installation process is fairly straightforward and I will do my best to walk you through the process below. Before you get started you will need a few tools for installation: 8, 10, and 19mm sockets, 12" extensions, Ratchet, 19mm wrench, Flat Head Screwdriver, Rotary Tool...
  view full answer...
  
• Trailer Hitch and Wiring for a 2005 Toyota Matrix
  Curt trailer hitch # C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then # C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have to use the ball mount recommended by the hitch manufacture so as not to void the hitch warranty. This will limit the amount of rise you can get to be able to tow the trailer level. Based on the picture you have sent you will need a good amount...
  view full answer...
  
• Parts Needed To Be Able To Tow a Trailer With a 2013 Lexus CT 200h
  While we do carry all the components that you will need to be able to tow a trailer with your 2013 Lexus CT 200h it is not recommended for trailer towing by Lexus. That said you are likely past any manufacturer warranties that would be voided so the decision is yours to make. You will need the Curt Trailer Hitch Receiver # C11200 to attach either the 1-7/8" # C45571 or 2" # C45572 Curt Euro Style Drawbar. You will need to match the ball size to the coupler on the trailer. You will need...
  view full answer...
• Best Towing Set Up For 2019 VW Golf Alltrack
  We can absolutely get your 2019 Volkswagen Golf Alltrack set up to tow your small utility trailer, and I'll detail all the parts you need, starting with the trailer hitch that fits, which is from Curt: - Curt Trailer Hitch Receiver # C11422 This hitch will fit your '19 Alltrack and is a really nice option because it has a concealed crosstube so the only thing showing is the receiver, which helps your VW keep its factory appearance. The other things you will need are a wiring harness and...
  view full answer...
• Hauling a Dirt Bike With a 2010 Toyota Corolla
  The best way to haul your dirt bike will be with a trailer as the frame of your 2010 Toyota Corolla is not strong enough to support that much weight on the hitch. The Curt Trailer Hitch Receiver # C11265 will allow you to haul a trailer with your Corolla. Your Corolla is rated to tow up to 1500lbs. You will also need the Hopkins Plug-In Simple Vehicle Wiring Harness # HM11141815 to operate the lights on the trailer. And a Curt Drawbar with 1-7/8" Ball # C45571. With that you will be...
  view full answer...
• Curt Trailer Hitch for 2006 Toyota Prius
  For a 2006 Toyota Prius I suggest the Curt Trailer Hitch Receiver, # C11468. This is a confirmed fit for all trim levels of the 2006 Toyota Prius. This is a Class I hitch with a maximum gross trailer weight of 2,000 lbs. and a maximum tongue weight of 200 lbs. It has a 1-1/4" x 1-1/4" receiver opening. If you will be doing some light towing and not use hitch only for accessories such as a bike rack, you will need wiring for the trailer lights. I suggest the T-One Vehicle Wiring...
  view full answer...
• Towing Capacity and Hitch Recommendation for 2013 Honda Accord Coupe and CVT Transmission
  According to the online copy of your owner's manual, your 2013 Honda Accord Coupe has a maximum total trailer weight limit of 1,000 lbs. This includes the weight of the trailer, cargo, and everything inside or loaded on top of it. While CVT (continuous variable transmission) vehicles aren't ideal for trailer towing, as long as you adhere to the limits outlined in your owner's manual, you shouldn't have any problems. I suggest confirming this information on your hard copy of the owner's...
  view full answer...
  
• Mounting Dimensions For Curt Trailer Hitch Receiver # C12123
  The Curt Trailer Hitch Receiver # C12123 has mounting holes that are separated 38-1/2" from drivers to passenger side on center. The lower mounting hole sits 2-3/4" below the upper mounting hole and they are separated 7-3/4" on the same horizontal line. This receiver is custom fit for the 2014-2022(current model year) Ford Transit Connect. I have included a image below with the measurements as well. Curt does recommend using either the 1-7/8" # C45571 or 2" # C45572 Euro Drawbar with this...
  view full answer...
  
• Does 2017 Chevy Cruze Diesel Have Towing Capacity and Parts Needed to Tow Small Trailer
  I took a look at the owner's manual for your 2017 Chevy Cruze and on page 261 it states "The vehicle is neither designed nor intended to tow a trailer" so I cannot recommend you do so, though the decision is of course up to you. If you do decide to tow, then you will absolutely want to go with the lightest, smallest of the trailers. For a diesel model of '17 Cruze the available trailer hitch from Curt is part # C11492, and since you mentioned 2" ball I assume you are also using the Euro...
  view full answer...
  
• Who Can Install a Trailer Hitch on a 2005 Chevy Corvette Convertible
  A motorcycle purist would say Ride that hog to Sturgis! But you and I know that is not always an option. Plus there is something about a Vette towing a Harley that is awesomely American. Talk about turning some heads! I checked with Curt and they have a Gold level installer at the Sears at the Lima, Ohio shopping mall who could install hitch # C11034 on your 2005 Chevy Corvette. A trusted mechanic or RV dealer with a service center could also perform the installation. Please note that...
  view full answer...
• Parts Needed To Tow a Trailer and Haul a Cargo Carrier With a 2016 Honda Civic Sedan
  Currently, a class I receiver like the Curt # C11604 that is rated for 200lbs of tongue weight and towing up to 2,000lbs is the only receiver available for your 2016 Honda Civic Sedan. There is not a receiver capable of supporting the weight of your Curt carrier fully loaded behind your Civic and this is most likely due to the structure under your Civic not being able to support the weight. The 19x47 Curt Cargo Carrier # C18110 will fit the class I receiver for your Civic. You will only...
  view full answer...
• Product Availability for Hauling a Honda Ruckus with 2017 Hyundai Sonata
  You have two options of a hitch for your 2017 Hyundai Sonata, the Curt Trailer Hitch Receiver, # C11402 and the Draw-Tite Sportframe, # 24965. I prefer the Curt option that is assembled in the USA and noted for having a superior powder coating. Each of these options have the same specs of being a Class I hitch with a 1-1/4" receiver. They are rated for a maximum gross trailer weight of 2,000 lbs. and a maximum tongue weight of 200 lbs. Meaning that the vertical load on these hitch options...
  view full answer...
• Trailer Hitch and Wiring Recommendation for a 2015 Infiniti Q50
  For your 2015 Infiniti Q50 the Curt hitch part # C11407 has been confirmed as a fit and would work well for you as long as the weight of your trailer when loaded would end up being less than 2,000 lbs total trailer weight and 200 lbs tongue weight. Now you would also need to check the owners manual of the vehicle to determine what the towing capacities are for it and stay under the lesser of the two capacities (hitch and vehicle.) For trailer wiring you would need the # C56248, for a ball...
  view full answer...
• Weight of Curt Trailer Hitch C11567 For 2020 Toyota C-HR
  I verified with the manufacturer for you that the weight is just 25 lbs for the Curt hitch that fits your 2020 Toyota C-HR, which is the following part: - Curt Trailer Hitch Receiver # C11567 I have added a link below to a video install of this hitch on a similar model year C-HR for you to check out if you'd like to take a look. Additionally, if you plan on doing some light towing with your C-HR you'll need some other parts as well, which I'll list out for you. - T-One Vehicle Wiring...
  view full answer...
• Hitch and Trailer Wiring Recommendation for 2013 Ford C-Max
  For your 2013 Ford C-Max the Curt trailer hitch part # C12092 would be a great option confirmed to fit. It's a Class II with plenty of capacity as well at 3,500 lbs trailer weight. For trailer wiring you'd then want the part # 119250KIT which is also a fit. For a ball mount you'd then want the part # C45571 for a 1-7/8 inch ball or part # C45572 for a 2 inch ball.
  view full answer...
• Recommended Trailer Hitch for 2018 VW Golf R Model
  I reached out to my contact at Curt and they have not yet tested the fit on your model. It is very likely that the Curt Trailer Hitch Receiver C11475 will fit your vehicle but the fit has not yet been confirmed. For the only confirmed fit we have for your 2018 VW Golf R model, I recommend the EcoHitch # 306-X7333. I've attached the installation instructions to help. The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56374 is also a very likely fit that...
  view full answer...
• Recommended Trailer Hitch Receiver and Wiring Harness For Trailer Towing With a 2008 VW GTI
  I recommend the Curt Trailer Hitch Receiver # C11074 for your 2008 Volkswagen GTI. I checked with Draw-Tite, EcoHitch and Stealth as they make the hidden receivers and none of them have anything to fit your GTI. The Curt does have a small 1-1/4" receiver that will keep the receiver up tight against your rear fascia and have the least impact on ground clearance. The receiver itself is rated to tow up to 2,000lbs with a 200lb tongue weight rating. Curt recommends their 2" Euro Ball Mount...
  view full answer...
• Curt Trailer Hitch Receiver Compatibility With a 2015 Buick LaCrosse With Dual Exhaust
  You will not have any issues mounting the Curt Trailer Hitch Receiver # C12115 on your 2015 Buick LaCrosse with the dual exhaust. Since this receiver fits a large selection of Buick, Chevrolet and Cadillac vehicles the installation notes will cover all the different vehicles but some steps like lowering the exhaust will not always be necessary. For your LaCrosse I do not see any need to lower the exhaust. Curt recommends using their Cam Buckle Stabilizing Strap # 18050 for any hitch mounted...
  view full answer...
• Which Trailer Hitch Fits 2014 Mercedes E-350 and Has Capacity for PWC Trailer
  For your 2014 Mercedes E350 Sedan the Curt hitch part # C11001 is a confirmed fit. The hitch itself has the capacity needed to tow a trailer with a 825 Sea Doo PWC, but you would need to check the owners manual of your vehicle to determine the vehicle's towing capacities and be sure to stay under them as well. For a ball mount you would want part # C45572 for a 2 inch hitch ball or the part # C45571 for a 1-7/8 inch ball. For trailer wiring you then would want the Tekonsha kit part #...
  view full answer...
• Recommended Trailer Hitch Receiver for 2018 Honda Fit Sport
  The Curt Trailer Hitch Receiver # C11406 is a fit for all 2018 Honda Fit models including the Sport. If you will be using this for a bike rack or other accessory, you will also need the stability strap # 18050 to keep your manufacturer warranty in tact. If you will be towing a light trailer, I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56395 and ball mount # C45571 or # C45572.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?