Recommended Hitch for a 2014 Acura TL
Updated 02/17/2026 | Published 06/13/2024
Products Featured in This Question
Question:
Hello my name is Marc, and Im messaging about choosing the right trailer for my vehicle. I own a 2014 Acura TL and Im taking the steps to tow a motorcycle, below 500 pounds. Between the Draw-Tite Class I and Curt Class I trailer hitch, which should i choose, is there even a difference?
asked by: Marc
Expert Reply:
Hey Marc! Between the Curt item # C11496 and the Draw-Tite item # 24899, I would go with the Draw-Tite Hitch item # 24899 because you see less of it after it's installed. Functionally, they both install in the same way and have the same capacities. The Draw-Tite is just tucked back in farther beneath your Acura.
Either way you go you will be limited to 1,000 lbs of towing capacity including your bike and trailer. Your 2014 Acura TL tops out at 1,000 lbs for towing capacity and you will want to go off of that number not the hitches capacities.
I have linked a couple of installation videos below along with the instructions so you can see how to get them set up.
Since you are planning on towing you will also need a wiring harness item # 46255 and the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258 for a 2 inch ball or item # 19256 for a 1-7/8 inch ball.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: draw bars
- Search Results: trailer wiring
- Shop: Vehicle Tow Bar Wiring
- Video: Set up: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2008 Honda Accord
- Q&A: Replacement Trailer Hitch Hardware Needed For A 2012 Acura TSX
- Q&A: Recommended Trailer Hitch Receiver and Wiring Harness For a 2014 Honda Accord Sedan EX-L
- Shop: Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 1-1/4" Hitch - 3-7/8" Rise - 3,500 lbs
- Shop: Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
- Shop: 2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: 2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000
- Search Results: hitch extender
- Video: Review of Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C56011
- Video: Trailer Wiring Harness Installation - 2014 Honda Accord
- Q&A: Difference Between 2 Curt Trailer Hitch Receivers that Fit the 2009 Honda Accord
- Q&A: Solution for 1-1/4 inch Hitch that Needs to Carry Bike Rack for 2 inch Hitch
- Q&A: Recommended Hitch To Install A Bike Rack On A 2012 Honda Accord Sedan
- Q&A: Least Obvious Trailer Hitch Receiver on a 2014 Honda Accord Sedan
- Q&A: What is the Towing Capacity of a 2013 Honda Accord Sedan V6
- Article: Trailer Maintenance Schedule
- Article: How to Measure for Trailer Hitch Drop
- Article: Determining Trailer Tongue Weight
- Article: How to Choose the Right Trailer Hitch Class
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
Jerred H.
2/17/2026
Hey Marc, how did things go with the Draw-Tite hitch on your Acura TL? Did it give you the clean look and towing setup you were hoping for with your motorcycle trailer? Your update could make it easier for others choosing between those two hitches.