Torque Spec for Axle Nut and Lug Nuts
Published 04/16/2024
Question:
I purchased 2 hubs for my trailer and need to learn the following torques What is the proper wheel lug torque? Also, What is the proper proceedure and preload torque for the hub axle nut. As I understand it, I need to preload axle nut to 30ft pounds to properly seat the nut. Then back off to 15. Follow by rotating nut counter clockwise for closest alignment and install cotter pin. My spindle straight not tappered. By all means, i want to install these hubs correctly. So Please advise if there is a better more correct way to seat the axle nut. Your help will be appreciated.
asked by: Brian
Expert Reply:
There is no specific torque setting for the axle nut with the # AKIHUB-440-2-G-EZ-1K. Check out the installation video below starting at the 13 minute mark. The hub is overtightened at first to make sure everything is seated. Then he backs off the castle nut until it is loose. After that, tighten it back until you get a little bit of pressure and make sure there is no play. Then you will check your holes for your cotter pin. For the lug nuts you're going to have 8-14" wheels and this has 1/2" studs so it will be 75-85 ft.-lbs.
(click to enlarge)
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Galvanized
- Trailer Hubs and Drums
- Idler Hub
- EZ Lube
- L44643 / L44643
- Marine Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 8 Inch Wheel
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: 205 70 14
- Video: etrailer Class III Trailer Hitch Installation Guide - 2024 Nissan Rogue
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,200 lbs
- Shop: Suspension Enhancement
- Video: DIY Install: etrailer Trailer Hitch Receiver on your 2023 Nissan Rogue
- Video: How to Install the etrailer Trailer Hitch Receiver on a 2021 Nissan Rogue
- Shop: Aluminum Trinity Series Trailer Wheel - 13" x 4-1/2" - 5 on 4-1/2 - Machined Black Fork
- Shop: Aluminum Margay Trailer Wheel - 13" x 4-1/2" Rim - 5 on 4-1/2 - Black Machine Finish
- Shop: Kenda Loadstar K371 Bias Trailer Tire - 4.80/4.00-8 - Load Range B
- Shop: Rambler ST205/75R15 Radial Trailer Tire - Load Range C
- Shop: Loadstar ST205/75D15 Bias Trailer Tire - Load Range C
- Shop: Karrier ST205/75R15 Radial Trailer Tire - Load Range C
- Search Results: hub
- Video: Trailer Axle with Idler Hubs Spec Review
- Q&A: Torque Specs for Axle Spindle Nut and Lug Nuts
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Search Results: 58846
- Shop: Headache Rack
- Q&A: How to Find Replacement Bearings and Grease Seal for 1990's Shoreline Boat Trailer
- Video: Dexter Trailer Idler Axle w/ Idler Hubs Spec Review
- Search Results: l68149
- Search Results: grease seal 58846
- Search Results: l44649
- Search Results: lug nut
- Q&A: Castle Nut Torque Spec for 3,500 Pound Axle
- Q&A: Torque Specs for 3500-lb 5-on-4-1/2 Dexter Hub/Drum 84546UC3
- Q&A: Replacement Wheel Bearings for Henschen Dura Flex 3.5K Axles
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Parts Needed To Add Electric Drum Brakes To Boat Trailer
on Trailer Hubs and Drums
