What 4-Inch Wide Stake Pockets do You Recommend for My Aluma Trailer?

Question

Question:

I need aluminum weld on stake pockets. 4 width to weld on to my aluma trailer

asked by: Bob B

1

Helpful Expert Reply:

The best option we have for 4-inch wide weld-on stake pockets are the Curt Stake Pocket for Flatbed Trucks or Trailers - Qty 1 # C83072. These particular pockets measure 3-3/4 inches wide x 3 inches tall. The pocket is designed for standard 2x4 boards, which measures 3-1/2" wide x 1-1/2" thick. I went ahead and attached a diagram that shows the dimensions of the pocket.

It is important to note that these are not made of aluminum.

expert reply by: Bob C

1

Dimensions of the Curt Weld-On Stake Pocket # C83072
(click to enlarge)

Answer 1

If the brand of axle is Rockwell we don't have a lift kit but if the torsion axle is a Dexter you could use the #K71-707-01 or if you have a Lippert #LC270682.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 5

Yes, the Dexter Self-Contained Hydraulic Jack #DX72CR does come with a manual hand pump that can be used as a backup in the event of hydraulic malfunction.

view full answer...

Answer 6

If you look at the brackets of the TorkLift HiddenPower Under-Vehicle Battery Mount #TLA7727 you'll see that the top hook goes much wider than the bottom one. There wouldn't be a frame dimension that this will work with since trailer frames…

view full answer...

Answer 7

I was unable to find any information with the numbers on your axle, unfortunately. However, you can contact the manufacturer of the trailer and they should be able to tell you exactly which inner and outer bearings you have. If for some reason they…

view full answer...

Answer 8

I went out to our warehouse and measured the Dexter Heavy Duty Suspension Upgrade Kit for Single Axle Trailers part #K71-358-00 for you. The dimension for the shackle kit are as follows: The distance between the top and bottom steel brackets is…

view full answer...

Answer 9

The trailer tire and wheel combo to fit your 10K Dexter axle would be the Taskmaster Provider ST235/85R16 Trailer Tire with 16" Vesper Silver Dual Wheel, #TA45FR. This wheel can be used as either the inner or outer wheel of a dual-wheel setup.

view full answer...

Answer 10

The Stake Pocket Tie-Down Anchor - Black Powder Coat - 2-1/4" D-Ring 4000lbs #WFSPDR requires a stake pocket that is no taller than 3-1/4" and at least 3-3/8" wide. This will fit your stake pockets that are 3" tall and 3-3/4"…

view full answer...

Answer 11

Your 2017 Chevy Silverado 2500HD will likely have either a 2" or a 2-1/2" trailer hitch receiver. You can confirm this by measuring the inside height and width of the receiver on your pickup (see attached). If you are trying to use a…

view full answer...

Answer 12

You would want to use 2, 1/2 inch diameter bolts that are 4 inches in length. I pulled a Fulton Fas-Lok Coupler #F343000301 and checked the installation instructions to confirm the bolt recommendations.

view full answer...

What 4-Inch Wide Stake Pockets do You Recommend for My Aluma Trailer?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching