Correct Torque Spec for 10" Steel Trailer Wheel

Question

Question:

How many foot pounds of torque are recommended for my 1998 Jayco Tent Trailer? Using 20.5/8.0-10 Load E Trailer Tire DOT 9DBU Tubeless 84M Load E Max Load 1107 @50 PSI. Manual says between 85 and 150. Big range.

asked by: Ron

0

Expert Reply:

The correct torque spec for a 10" steel trailer wheel like the Steel Solid Center Trailer Wheel part # AM20053 is between 75 and 85 ft. lbs.

expert reply by: Conner L

0

Answer 1

In order to flat tow your 2016-2018 Ford Focus without adaptive cruise control I recommend starting with the Roadmaster EZ5 Base Plate Kit - Removable Arms #RM-524443-5. These base plates will give you a really clean look when installed and will work…

view full answer...

Answer 2

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Correct Torque Spec for 10" Steel Trailer Wheel

Product Page this Question was Asked From

Continue Researching