Can Kodiak Hub # KHR10D Replace Trailer Hub TDE 46245

Question

Question:

The replacement hub is Kodiak #KHR10D can I still use same brake calibers Trailer hub TDE 46245 Min. Thk. .850

asked by: Robert W

1

Helpful Expert Reply:

From previous customers we've determined that the Kodiak replacement hub/rotor part # KHR10D that you referenced will work as a replacement for the TDE hubs like the 46245 that you have.

expert reply by: Jameson C

1

Answer 1

The TDE 46245 you have is a Hub and Rotor for a 3500lb axle and uses inner bearing #L68149 and outer bearing #L44649 and uses the 5 on 4-1/2" bolt pattern For a replacement idler hub you can use the Trailer Idler Hub Assembly for 3,500-lb E-Z…

view full answer...

Answer 2

According to my research your TDE 46845 trailer hub fits a #84 spindle so the replacement bearing and seal kit you need is part #BK2-100. This is for a single hub so you'll need to adjust the quantity as needed. Attached is a video showing this…

view full answer...

Answer 3

To determine if the Kodiak rotor #KHR10D will fit the trailer you will need to go by the inner and outer bearing numbers stamped into the sides of the bearings. This rotor uses inner bearing L68149 and outer bearing L44649. Even if the bearing…

view full answer...

Answer 4

I believe you meant a TDE 46245, is that correct? If that's the case, you've got a 3500 lb axle which uses a 10 inch hub/rotor with a 5 on 4-1/2 wheel bolt pattern. You'll want to use the Kodiak #KHR10D hub/rotor as a replacement. The hub…

view full answer...

Answer 5

Unfortunately, just the outer bearing is not quite enough to figure out what you need for replacement hubs and bearings. For a trailer with that much weight it sounds like you have a tandem trailer. I recommend replacing the bearings and seals on all…

view full answer...

Answer 6

It's only really necessary to replace the axle if the spindles are damaged as they not a wear item but we do have the correct hubs/drums and brakes you need. This comes back as a 3,500 lb axle so you will want to use the Trailer Hub and Drum…

view full answer...

Answer 7

I reached out to my contact at Kodiak regarding the Disc Brake Kit #K2R1058D11E and he said the rotor/spacer bolts need to be torqued down to 90 foot pounds and the caliper clip bolts will be torqued down to 45 foot pounds. I have attached a video…

view full answer...

Answer 8

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 9

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Can Kodiak Hub # KHR10D Replace Trailer Hub TDE 46245

Product Page this Question was Asked From

Continue Researching