Is There a Lift Kit for a Jayco Jay Feather EXP 213 Trailer

Question

Question:

Seeking out which lift kit would work for this make and model. Looking for around 3inch of lift. Appreciate the help! Tandem Dexter Axle. From the imprint: Mod 10H SLR 13.3. 3000# capacity each.

asked by: Winton

0

Expert Reply:

The Jayco Jay Feather EXP 213 likely uses a Dexter Torflex #10 Axle. If that is the case, then you can use the Torflex Lift Kit part # K71-707-02 to lift the trailer 2-5/8". This should be a direct bolt-on kit with cutting or welding.

expert reply by: Conner L

0

Answer 1

For a brake controller I would recommend the Prodigy P2 Brake Controller part #90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The lift kits we carry fit with specific axles; the #K71-725-02 is a tandem axle application and will give a 3-1/8" lift and is compatible with side-mounted #12 Torflex axles with 5,500-7,000-lb capacities. If that is what your axle is, this kit…

view full answer...

Answer 5

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 6

The Road Armor Shock Absorbing Equalizer Kit part #LC696740 are taller than most other standard equalizers so you'll likely need the longer 3-1/8" shackle straps when using them, the Lippert AP Kit part #LC52SV is a go-to for this as it has…

view full answer...

Answer 7

Hello Rene, thanks for reaching out. It is pretty typical for RV manufacturers to use axles that are not rated for the full GVWR. They say this is because 10%-15% of the camper weight is on the hitch instead of the axles. They will put the bare…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 11

Trailer manufacturers don't usually keep a record of parts like these that they install at the factory, so I cannot be sure as to the exact length of the shackle strap that would have come originally on your trailer. With this in mind, a 3-1/8…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Is There a Lift Kit for a Jayco Jay Feather EXP 213 Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching