Replacement Spindle Compatible with Tie Down Engineering 46210 Hubs

Question

Question:

What size spindle do I have if I have tie down engineering 46210 hubs? Looking for a replacement.

asked by: Nicholas B

0

Expert Reply:

You have a standard 3500 lb axle, which uses a # 84 spindle compatible with a L68149 inner and an L44649 outer bearing.

We offer a few replacement # 84 spindles with different stub diameters.

• For an E-Z lube spindle with a brake flange and a 1-3/4 inch diameter stub, use # TRU74FR
• For a standard spindle without the brake flange and a 2 inch diameter stub, use # TRU24FR

expert reply by: Mike L

0

Answer 1

We have just what you are looking for. I called my contact at TDE and asked about the hub you have on your boat trailer. They told me that it was a 5-stud idler hub for a 3,500-lb axle. That means you need the part #AKIHUB-545-35-K. This is a fit for…

view full answer...

Answer 2

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 3

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Kevin, your Valley Odyssey brake controller hasn't been made for so long that there aren't any replacement parts available for it. Actually Valley isn't even in business anymore. If you were looking for a reason to "treat yo…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hello Jeremy, thanks for reaching out. The Air Lift Air Helper Spring Cradles #AL59DQ will only work with the Air Lift brand bellows-style air bags. They will not work with the Firestone air bags.

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

Hey John, the Air Lift kit part #AL57230 that fits your 2007 Dodge Ram 1500 is compatible with in-bed hitches but not mega cab models. The part #AL57295 is a fit for the mega cab models and fits with in-bed hitches. The part #AL88295 fits mega cab…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Spindle Compatible with Tie Down Engineering 46210 Hubs

Product Page this Question was Asked From

Continue Researching