How Tight Should Spindle Nut Be on Trailer Axle
Published 03/31/2020
Question:
I have a 16foot Corn Pro, Landscape Trailer and need to torque the axle nut. What is the correct torque pound for this trailer? Nothing online seems to list this. Thank you,
asked by: Mike S
0
Expert Reply:
Trailer axle nuts don't have a torque rating as you don't want to run them down super tight. The trick is to tighten the nut till there's no play in the hub in and out with the wheel installed and then use the cotter pin to hold the nut in place. This allows the hub to seat properly without creating too much friction that would cause damage to the bearing/hub.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly for 2,000-lb Axles - 7" - 5 on 4-1/2
- Trailer Hubs and Drums
- Hub with Drum
- Standard
- L44649 / L44649
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: trailer tires and wheels
- Search Results: lc175225
- Search Results: apubr~50
- Search Results: 091148
- Search Results: 13~141~3
- Search Results: 093161
- Search Results: hitch
- Shop: Trailer Hitch
- Shop: Dexter 5-Leaf Slipper Spring w/ Flat End for 10,000-lb Trailer Axles - 30-1/2" Long
- Shop: Replacement Square, Direct Weld Jack Inner Tube with Spring-Return Drop Leg
- Shop: Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" - Left Hand - 7,000 lbs
- Shop: Lippert Components Clear Oil Cap Kit - 8K
- Shop: Dexter Brake Actuator w/ Electric Lockout - Disc - Primed - 5 Position Adjustable Channel - 20K
- Shop: Dexter Zinc-Plated Brake Actuator w/ Drop - Drum - 2-5/16" Ball - Bolt On - 20,000 lbs
- Shop: Dexter Hydraulic Brake Actuator w/ Drop and Electric Lockout - Disc - Zinc - 2-5/16" Ball - 20K
- Q&A: Can Drum Brake Actuator Be Used Temporarily on Trailer with Disc Brakes
- Q&A: Brakes Lock Up On Trailer When Plugged Into 2015 Chevy Silverado 2500
- Q&A: Trailer Brakes Lock Up When Connected to Truck
- Video: Checking Out the Cast Trailer Coupler
- Video: An In-Depth Look at the Dexter Zinc-Plated Brake Actuator w/ Drop
- Article: How to Measure a Trailer Axle
- Q&A: Can I Replace 8-14.5 Tires with a Non-Metric Sized Tire
- Q&A: Wiring a Switch to the Dash to Control Power to a Gate on a Dump Trailer
- Video: Mount: Curt Custom Fifth Wheel Installation Kit for Chevy/GMC on a 2008 GMC Sierra
- Q&A: How to Charge Two 6V Batteries Wired in Series
- Video: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles Review
- Video: Mount: Mounting Bolts and Hardware for 10" Brake Assemblies on a 1917 Ford Model T
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Printable Trailer Bolt Hole Pattern Template
- Q&A: Correct Replacement for Atwood 71119 Landing Gear Motor
Explore Expert Info
![Our Expert]()
on Trailer Hubs and Drums
on Trailer Hubs and Drums
