Preventing Trailer Hitch Rust
Updated 02/02/2020 | Published 02/01/2020
Products Featured in This Question
Question:
Hi, Buying my next hitch - Curt C13264. All past hitches rust and require touch up/paint, etc. This is especially so inside the open ended tubes. Road dirt, salt, etc. collects in the tubes and rusts badly. Should/Can I cover the tube ends with a tape flapper cover to allow drainage, to help prevent this issue?? Thanks
asked by: SteveO
Expert Reply:
Keeping a trailer hitch in mint condition is impossible but there are a few steps you can take to prolong the life of your Curt # C13264 trailer hitch and fight the rust that you were talking about. A hitch cover like the etrailer Rubber Hitch Cover for 2" Trailer Hitches # 22282 helps keep out debris and rust causing agents.
Rinsing off any salt that would get on it during winter months is key as well as some anti-corrosive paint that you can apply to any places where you may have a scratch like from rocks. If you cannot find anti-corrosive paint, then applying some spray paint will help resist rust and be better than nothing.
Included are video resources for these solutions.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 900 lbs TW
- 6000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 900 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Search Results: molle
- Search Results: hitch light
- Search Results: receiver reducer
- Video: A Closer Look at the Gen-Y Hitch Running Boards with Custom Installation Kit
- Shop: Suspension Enhancement
- Shop: Curt Rubber Hitch Cover for 2-1/2" Trailer Hitches
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Video: Feature Review BullRing Stake Pocket D-Rings-BU94VR
- Shop: Nerf Bars - Running Boards
- Shop: Ladder Rack
- Shop: Mud Flaps
- Shop: Vehicle Cargo Control
- Shop: Roof Rack
- Shop: Gen-Y Hitch Running Boards w/ Custom Installation Kit - 6" Wide - Black Steel
- Video: How to Set Up Your Curt Trailer Hitch Receiver on a 2010 Honda CR-V
- Video: All About the Hitch Reducer 2" to 1-1/4" Trailer Hitch Receiver
- Q&A: What Size Bolts are Used to Install Draw-Tite # 75547 on a Honda CR-V
- Q&A: What Size Bolts Secure the Draw Tite Hitch # 75547 to 2010 Honda CR-V
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Trailer Hitch Receiver Adapter - 2" to 1-1/4" - 4-3/8" Long
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Hitch Adapter 2" to 1-1/4" Trailer Hitch Receiver - 7" Long
- Shop: Hitch Reducer 2" to 1-1/4" Trailer Hitch Receiver
- Video: Brads Honest 6 Month Review - Air Lift AirLift 1000 Air Helper Springs
- Video: Air Lift AirLift 1000 Air Helper Springs Review
- Video: Choosing the Right Vehicle Suspension Upgrades
- Article: Trailer Hitch Receiver Sizes
- Search Results: anti rattle
- Q&A: Recommended Hitch for a 2023 Subaru Forester
on Trailer Hitch
