How to Use Power Drill to Make Raising and Lower Scissor Jacks for Camper Quicker

Question

Question:

I was wondering if I can use a drill such as a impact drill to raise and lower the jacks quicker

asked by: Joe

0

Expert Reply:

Yes, you can use a drill to make raising and lowering the scissor jack set part # JSC-24 a bit quicker. You'll just need the drill adapter part # UF48-979005 too and you'd be set. This basically is a socket attached to a power drill shank. The size socket that comes with this is 3/4 inch.

See review video I attached for this as well.

expert reply by: Jameson C

0

Answer 1

Determining the correct weight distribution system is dependent on the total tongue weight of your trailer. Ideally you want your total tongue weight to be in the middle of the range of the weight distribution system you choose. To measure the total…

view full answer...

Answer 2

The best way to determine which weight distribution system with sway control to use on a setup is to base it on the tongue weight of the setup. You will also need to consider any weight that is behind the rear axle of the tow vehicle as tongue weight…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver #13333 referenced in your question is confirmed to fit your 2004 Dodge Ram 1500 as long as you replace what you have with the standard OEM bumper. The Curt hitch is going to attach to the truck's factory bumper…

view full answer...

Answer 4

Because it's oddly shaped, it's difficult to provide an overall length, as it will depend on where you measure from and your dimension includes the factory mirror width as well. However, when installed, the #LO34FR Longview Slip On Towing…

view full answer...

Answer 5

Hey Jack! First of all, congrats and the soon to be new travel trailer! Ideally the correct WDS is going to put your trailer's tongue weight right around the middle. It looks like your trailer comes in at 9,630 lbs, so if we figure 15% of that…

view full answer...

Answer 6

For a pair of stabilizer jacks that would have more than enough capacity that would work well on your R-Pod I would recommend the Stromberg Carlson Trailer Scissor Jacks part #JSC-24. These have a 5k capacity per jack and would do a great job as long…

view full answer...

Answer 7

Personally Russ, if you are planning to keep your 2018 Grand Design Momentum 351M toy hauler and want to benefit from a better ride then upgrading to the Roadmaster Comfort Ride Leaf Spring Suspension Kit #RM-2460-2570 makes the most sense. If you…

view full answer...

Answer 8

Yes, you can use a 2-1/2" to 2" trailer hitch sleeve adapter with a weight distribution system. I recommend the Trailer Hitch Receiver Reducer Sleeve part #e33YR which has a 3" to 2-1/2" and a 2-1/2" to 2" for this. The…

view full answer...

Answer 9

The Dexter Equalizers #K13-142-02 you have on your tandem axle travel trailer can absolutely be replaced with the MORryde 14-3/4" Shock Absorbing Equalizers for Tandem Axle Trailers w/ 42" Wheelbase - 8K #MR34AR you mentioned, as they are…

view full answer...

Answer 10

It appears you have 6K tandem axles. We have a few options for the replacement leaf spring but you will need to measure your spring center of the bolt to center of the opposite bolt to get the correct fit. I've linked the options for you. Then I…

view full answer...

Answer 11

I understand your worry Tom, and I have a couple recommendations. First is the MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR which has a height of 4-1/2" for the mounting bolts. This is also 6-1/2" in width like the shorter…

view full answer...

How to Use Power Drill to Make Raising and Lower Scissor Jacks for Camper Quicker

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching