Powering Interior Trailer Lights With Generator

Question

Question:

Hi our high school band program has a 24 ft cargo trailer with 7pin connector. We’d like to use a generator with built in 8amp dc inverter to power 12v lights in the trailer interior cargo lights not running or brake lights. Can I just splice a dc plug into the main 12v power and ground cables in 7 pin connector to achieve this?

asked by: Greg

0

Expert Reply:

You may splice your generator into the main 12V power and ground from the trailer's 7 pin connector to power the interior lights if you use an inline fuse like part # SWC9538 and fuse part # C58450-1 between the 7-pin 12V wiring and the generator 12V outlet. I recommend to wire in the power and ground to the Optronics 12V DC power plug part # A-200 to plug into the generator. The Optronics plug is rated for 12 amps. You want to use an inline fuse because if the wiring shorts out it can back feed into the generator and blow a fuse in the generator or fry the wiring in the 12V plug.

If you need a generator I recommend the etrailer.com generator part # 333-0003 that features a 12V plug outlet and an electric remote start. It also has built in safety features to prevent overload. The generator is designed with a 12V 8.3-Amp outlet.

expert reply by: Heather A

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 8

E-tracks are typically the stronger of the two, but X-track is more versatile since you can mount them horizontally or vertically. Choosing between the two really depends upon how you plan to use them. If you are installing something in a truck bed,…

view full answer...

Answer 9

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 10

The Dexter Trailer Idler Hub Assembly for 3,500-lb Axles item #84545UC1-EZ fits a item #L68149 bearing which has a 1.378" inner diameter. I would not recommend using this hub on a boat trailer. Instead, you'll want a galvanized one like item…

view full answer...

Answer 11

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 12

Hi Jeff! So the only combo with the 5 on 4-1/2 inch bolt pattern we have that provides that Load Range E rating is the Taskmaster Provider #TA56AR. It doesn't look like that tire is available by itself, either. This would certainly give you more…

view full answer...

Powering Interior Trailer Lights With Generator

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching