Bearing Kit with LM67048 and L44649 Bearings

Question

Question:

I have a camper 1995 Mallard by Fleetwood. Looking for the kit # with bearings ,races, seal and lock washer to order. I have a outer bearing # L44649 inner bearing # LM67048 seal # 10-42

asked by: Bruce

0

Expert Reply:

I do have all of the parts you need but we do not offer an all inclusive bearing kit with them. Instead, you will need to purchase each separately using the list I have attached for you below.

Inner Bearing - part # LM67048
Inner Race - part # LM67010
Outer Bearing - part # L44649
Outer Race - part # L44610
Grease Seal - part # 10-42
Tang Washer - part # 5-101

expert reply by: Conner L

0

Answer 1

Between the Curt Echo #C51180 and Redarc Tow Pro Elite #RED44FR for your 2019 Nissan Titan I recommend the Redarc as it is a one time install, and very out of the way unlike traditional trailer brake controllers. To install the #RED44FR in your Titan…

view full answer...

Answer 2

The Dexter 8-283 is an obsolete 2800lb 10 x 1-1/2 inch hub that used a LM67048 inner and a L44649 outer bearing. Unfortunately, we don't have any hubs that would be compatible with the spindles on your axle. Your best bet at this point would be…

view full answer...

Answer 3

The 10" x 1-1/2" Electric Brake Shoe/Lining #bp04-065 that you referenced can be used on both the right and the left had side brake assemblies normally seen on Dexter 2.8K axle.

view full answer...

Answer 4

What you were told was only partially correct. If you wanted to replace the entire brake assembly but you had welded on brakes then you could not replace the assemblies. However, you can replace the worn brake parts. There should be a number on the…

view full answer...

Answer 5

Like you said, 10 x 1-1/2 inch brakes are hard to find. We currently do not offer any in that size. But the shoes, #bp04-065, are a fit for Dexter 10 x 1-1/2 inch brakes. The issue is that the axles associated with the Dexter 10 x 1-1/2 inch brakes…

view full answer...

Answer 6

For the inner bearing you need #LM67048 and race #LM67010. The outer bearing is #L44649 and race #L44610. The seal is #10-42.

view full answer...

Answer 7

We do have a solution for replacing your obsolete Dexter trailer axle but it isn't your standard trailer axle as none of ours matches that description. If you want to stick with a standard axle you need to contact a trusted trailer shop to have…

view full answer...

Answer 8

With your axle being a 2-1/2" diameter it sounds like you will need either our etrailer Axle #e45SR or the Dexter #7685269-EB. Both of these are 3,500lb axles with the 4" drop a 95" hub face and electric brakes included. You will only…

view full answer...

Answer 9

We don't have an install video on this exact axle, the Trailer Axle w/ Electric Brakes - 4" Drop - 5 on 4-1/2 Bolt Pattern - 95" Long - 3,500 lbs part #e45SR, but I did do one on a similar style which I have attached for you below. It…

view full answer...

Answer 10

The two options you're referring to, the Dexter Trailer Axle w/ Electric Brakes #7685269-EB and Trailer Axle w/ Electric Brakes #e52SR are essentially the same when it comes to their specs. The only difference is the manufacturer with one being…

view full answer...

Answer 11

Based on the measurements and bearing numbers you provided me. We have the individual parts you need. You'd want the bearing part #LM67048 and #L68149. Since the inner diameter of bearing #LM67048 is 1.250 inches and the inner diameter of bearing…

view full answer...

Answer 12

If the seal journal surface on your spindle is damaged to the point where the grease seal compatible with your hub won't contain the grease in the hub, the only acceptable way to proceed is to replace the spindle or the axle. Because welding…

view full answer...

Bearing Kit with LM67048 and L44649 Bearings

Product Page this Question was Asked From

Continue Researching