Least Visible Trailer Hitch Recommendation for 2017 Toyota Sienna
Question:
I have a new 2017 Toyota Sienna SE, I would like to put a trailer hitch on. The Curt 13105 looks relatively easy to install, especially with your video. But, I would rather use the Curt C13343 for a more custom look. I have watched the C13105 video and it makes complete sense, but the written instructions for the C13343 have you taking off the back facia. The underpanel makes sense, but I cant see any reason to take off the rear facia. it uses the same bolt holes as the C13105. It is up behind the rear facia, but nothing seems to be in the way. Can the C11343 be installed without pulling off the rear facia. My van has 50 miles on it and I a little itchy about removing exterior visible body parts. Is there an installation video for the C13343. Thanks for your help.
asked by: Brian B
Expert Reply:
Of the 2 inch Curt hitches we offer for your 2017 Toyota Sienna the part # C13343 is the one to go with as it has only the hitch opening visible down below the bumper.
The instructions do recommend removing the rear fascia to install the hitch. We sometimes find that there can be shortcuts made to install hitches but in general that is not the case. We currently don't have an install video for this hitch yet either.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: DIY 2017 Toyota Sienna Installation for the Curt Trailer Hitch Receiver
- Search Results: curt 13343
- Video: How to Install: Curt Trailer Hitch Receiver on your 2014 Toyota Sienna
- Video: Set up: Curt Trailer Hitch Receiver on a 2014 Toyota Sienna
- Search Results: tube brush
- Search Results: wire brush
- Search Results: nylon brush 814092
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver (Class II Only)
- Video: How to Install: Curt Trailer Hitch Receiver on your 2018 Toyota Sienna
- Shop: Trailer Wiring
- Video: Hopkins Custom Fit Vehicle Wiring - Trailer Hitch Wiring - HM43494 Review
- Q&A: Recommended Trailer Hitch for 2019 Toyota Sienna for Ground Clearance
- Q&A: Trailer Hitch Recommendation for 2018 Toyota Sienna with Best Ground Clearance
- Q&A: Most Hidden Trailer Hitch Receiver For a 2018 Toyota Sienna
- Q&A: Difference of Class III Trailer Hitches for 2018 Toyota Sienna
- Q&A: Hitch for 2017 Toyota Sienna with Best Ground Clearance
- Q&A: Does Draw Tite or Curt Hitch for 2017 Toyota Sienna have Best Ground Clearance
- Shop: etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Finding the Right Trailer Wiring Harness
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Trailer Wiring Diagrams
on Trailer Hitch
B H.
6/14/2020
I am having trouble getting the 5th and 6th screws in (the two closest to the engine on driver and passenger side. It seems out of tolerance where the hitch hole is not aligned with screw insert, so the screw cannot be inserted. Anyone else have this problem?