Removing and Replacing Trailer Spindles
Question:
I have a question about spindles , I know how to replace hubs on my pontoon trailer. But how do I change the spindles. Do they bolt on or have to be welded to axle. Thanks
asked by: Tiny G
Expert Reply:
To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel tracking problems. I would recommend finding a welder who is experienced with trailer axles. Your local RV dealer or repair facility could probably refer you.
In many cases, it's less expensive to simply replace the trailer axle itself. We offer a basic selection of replacement 2000 and 3500 lb axles. If you'd care to reply with the following information, I'd be happy to make a recommendation for a replacement axle. I'll need to know the reference numbers off the inner and outer wheel bearings as well as the hub face to hub face dimension and the distance between the spring seats, measured center hole to center hole. I'll provide some diagrams showing how to get these measurements.
Product Page this Question was Asked From
Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide
- Trailer Spindles
- Standard Spindle
- 1-1/2 Inch Wide
- Square
- For 3500 lb Axle
- TruRyde
more information >
Continue Researching
- Shop: RV Bearing
- Video: Review of Kenda Trailer Tires and Wheels - Tire with Wheel - KE45EV
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Search Results: trailer hubs and drums
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Q&A: Process for Changing a Damaged Spindle on a Trailer Axle
- Video: What to Know About the Trailer Hub Assembly
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Trailer Hitch
- Shop: Trailer Hub Assembly - 2,200-lb E-Z Lube Axle - 5 on 4-1/2 - 13" - 15" Wheels - Galvanized
- Shop: Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Trailer Axle Beam with EZ-Lube Spindles - 89" Long - 3,500 lbs
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Wiring
- Video: Measuring To Choose The Right Trailer Axle
- Search Results: trailer wheel studs
- Article: Trailer Wiring Diagrams
- Q&A: Troubleshooting Snowmobile Trailer With Loose Hub
- Video: Spindle Nut Kit for EZ Lube Axles: The Breakdown
- Video: Installing the etrailer Easy Grease Trailer Idler Hub Assembly
- Search Results: castle nut
- Search Results: spindle nut
- Q&A: Replacement Hub/Drum Assembly Needed For A Older Boat Trailer
- Q&A: How to Tell if a Trailer Spindle is Damaged or Needs to be Replaced
- Shop: Brake Controller
- Search Results: spindle nuts
- Search Results: castle nut retainer
- Q&A: What is the Best Grease for Trailer Bearings
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
on Trailer Spindles
Jesse
8/10/2020
Hi! Thank you very much for the feedback, had a quick question for you. Do you know if a machine exists to put together a spindle and an axle? Thanks!