Customers compare KE45EV to these similar products
Products Featured in this Video
Hello, everybody. This is Jeff at etrailer.com. Today, we're taking a look at the Kenda Karrier ST ST175/80R13 radial trailer tire in a load range C, and it's mounted on this 13-inch galvanized spoke steel trailer wheel with the 5 on 4 1/2-inch bolt pattern. Now this tire wheel assembly is ideal for stock trailers, utility trailers, and even campers. The wheel is a sturdy steel wheel with… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Glad to hear you are safe and able to check the problem out. It sounds like there could be a number of things causing the problem. An EZ-Lube system would not cause the issue because it is normally just the access to the fitting that is changed for…
view full answer...The best tire for your trailer will really depend on how much time you spend on paved roads versus dirt or gravel roads. At the 175/80-13 tire size, you can choose between a radial tire and a bias ply tire. Radial tires, like part #AM10210, have more…
view full answer...The ST175/80D13 tire you added shouldn't be a problem. It will be slightly larger in width by about 1/4" and diameter by about 1/2" but that is unlikely to cause clearance issues. However, if you want to keep running that tire on there…
view full answer...Replacement of a spindle on a trailer axle is best left to a professional installer. This is not a do-it-yourself type of project. We urge you to use a professional welder experienced in axle fabrication. Proper alignment and welding are critical to…
view full answer...To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel…
view full answer...Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…
view full answer...An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…
view full answer...In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…
view full answer...The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…
view full answer...The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…
view full answer...The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…
view full answer...