Replacement Lid for Fan-Tastic Vents Trailer Roof Vent with Piano-Style Metal Hinge

Question

Question:

Will this fit? Looks like it will. Item # FVK1020-19

asked by: RICHARD M

0

Expert Reply:

Yes, part # FVK1020-19 is the replacement vent lid for the Fan-Tastic Vent models that use a long piano-style hinge. This is the only such part we offer from Fan-Tastic Vent. If you ever need a new motor assembly we offer that too, part # FVK8017-00, which consists of the bow-tie bracket, motor, and blade.

expert reply by: Adam R

0

click to enlarge

Answer 1

Hey Rick, I reached out to ASA Electronics and they stated that the VCMSYL50IR/VCMSYL50IL has a different housing than the other cameras and it's unfortunately not sold separately so you'd have to just get the housings you currently have…

view full answer...

Answer 2

If your Dometic 620526.321 doesn't have an air distribution box then you would need to determine how it's attached to the roof. The units we carry, like the Advent Air Replacement RV Air Conditioner #ACDOM150, require an air distribution box…

view full answer...

Answer 3

The MaxxAir TuffMaxx Replacement Shroud #MA00-325001 that you referenced will work well on your horse trailer's A/C unit. I spoke with my contact at MaxxAir and Coleman-Mach and confirmed the replacement shroud will fit your unit. Based on my…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Lid for Fan-Tastic Vents Trailer Roof Vent with Piano-Style Metal Hinge

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching