Troubleshooting Extang Trifecta Clamp that is Stuck After Unscrewing

Question

Question:

I unscrewed the cap but the clamp wont come loose from the truck bed. I can I get the clamp off without breaking it?

asked by: Tom F

0

Expert Reply:

If the clamp like the part # EX1034 is tight even after unscrewing knob that would mean it's either seized up and would need to be sprayed with some WD-40 to try and release it or it is some how binding up to the shaft of the threads.

You would want to gently pry on it to try and get it to release.

If it's damaged you would need the part # EX1034 to replace it.

expert reply by: Jameson C

0

Phil H.

2/22/2024

I tried WD-40 for the same problem. It won’t budge. Can’t figure out how to get those things off!

Reply

Jameson C.

2/26/2024

@PhilH If you can't get the clamp to turn grab a set of channel locks or pliers to grip it and get more leverage. If the knob turns but nothing loosens that means the threaded stud is spinning with it. Grab the threaded portion with a set of vice grips to keep it from turning as you turn the knob.

Reply

Answer 1

None of the methods are super easy. I'd recommend three though you have to remove hinges. This is least invasive, doesn't require cutting the cover, and also doesn't risk damaging cover.

view full answer...

Answer 2

I spoke with my contact at Extang regarding the removal of the existing cab clamp on your Trifecta Tonneau Cover. She stated that on the Trifecta covers, after you have removed the screws that hold the cross member in place, you will then need to…

view full answer...

Answer 3

I spoke with my contact at Extang about the install of the front clamp for Trifecta Cover Clamp part #EX1034 that you referenced and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab…

view full answer...

Answer 4

No you cannot replace the front clamps of the Extang Trifecta 2.0 Soft Tonneau Cover #EX92430 with the Replacement Tail Clamp Assembly #EX31003005. The front and tail clamps are different in order to keep the tonneau cover securely in place and thus…

view full answer...

Answer 5

I spoke with my contact at Extang regarding your situation and he said that you have a couple possible options to gain access to the lock assembly inside your Canyon's truck bed. You can first try removing one of the hinge caps on the outside of…

view full answer...

Answer 6

I found the picture you mentioned and while I wasn't able to find a better version that has easier to read text I can retype out the text of each step to make it easier to understand. Step 1. With the cover supported and laying flat, remove the…

view full answer...

Answer 7

I spoke with my contact at Extang about the install of the front clamp for Trifecta Cover part #EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly will then be…

view full answer...

Answer 8

I spoke with my contact at Extang a while back about the install of the front clamp for Trifecta Cover part #EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly…

view full answer...

Answer 9

When installing the Replacement Cab Clamp Assembly #EX1034 on your Extang Tonneau Cover you will first need to remove the screws from the crossbow/support rail of the cover. This is what will allow you to both remove the existing/damaged cab clamp as…

view full answer...

Answer 10

I spoke with my contact at Extang and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly will then be able to slide out of the rail.

view full answer...

Answer 11

We do carry the replacement hinge part #EX1033 for your Extang Trifecta. We also carry the replacement cab clamp part #EX1034 that you referenced.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Troubleshooting Extang Trifecta Clamp that is Stuck After Unscrewing

Product Page this Question was Asked From

Continue Researching