Replacement Trailer Roof Vent Lid for Sundowner Horse Trailer

Question

Question:

HI, Any idea which vent cover I need for the attached picture its off a Sundowner horse trailer

asked by: Philip

0

Expert Reply:

It looks like your Sundowner roof vent is a standard 14 x 14-inch size with a continuous-type hinge. For such a vent we offer the Ventline Vent Cover for Old Style Rounded Dome Trailer Roof Vents # BV0554-03 (smoke) and # BV0554-01 (white). We also offer a flat-profile metal lid, part # BV0534-00. The linked video shows the process of replacing the lid.

expert reply by: Adam R

0

click to enlarge

Answer 1

The replacement vent cover for your Sundowner horse trailer can be different as vents are often changed over the years by manufacturers. The vent cutouts remain consistent because there is an industry standard size so replacements are available but…

view full answer...

Answer 2

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 3

The most similar solution we offer would be the MaxxAir part #MA00-04000K which has a white lid, manual lift, and a 12 volt fan, but we do not have a Fan-Tastic roof vent that has a white lid.

view full answer...

Answer 4

Check your power source, ensure you have voltage to your MaxxFan, MA00-04000K. Use a voltmeter to ensure your battery is delivering the required voltage (no less than 11-volts). If this is a new install please verify that you connected wiring…

view full answer...

Answer 5

The physical difference in terms of appearance between various well-known gooseneck coupler manufacturers is hard to spot because they all are fairly similar. The biggest difference comes with the width of the coupler flange. The best way to…

view full answer...

Answer 6

I'm not quite sure what you mean by the "heart", however for your Ventline VD0434 we have the replacement screen frame #BVA0444-32, the replacement lid #BVD0449-A01, and the replacement ceiling garnish #VA0445-28 all available for…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Linda, Yep, it sure will; the WeatherTech Roll Up SunShade Kit #WT87QV will indeed fit your 2024 Nexus Viper 27V. This is a good choice as it is double-sided with one reflective side to keep the sun (and heat!) out of your motorhome, with the…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 12

Hey Dave, the wiring that comes with the etrailer RV Solar Panel Kit part #e59FV is 7.5 meters long. I attached a diagram that shows how multiple panels attach to the controller. This is compatible with lithium batteries too. Is this first time with…

view full answer...

Replacement Trailer Roof Vent Lid for Sundowner Horse Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching