Replacement Hub for a Lippert LCI 126003 Hub

Question

Question:

My hubs are Lippert #126003 will this replace them?

asked by: Mike

0

Expert Reply:

I was able to find the 126003 hub and was able to determine that it is a 3,500 lb hub/drum with a 5 on 4-1/2 inch bolt pattern just like the # AKHD-545-35-K that you referenced. This hub will work as a replacement for your Lippert.

expert reply by: Jameson C

0

Answer 1

The Taylor Made Marine Gas Strut for Boat Hatches part #3691824-10 is as close as I can get you. It offers an overall extended length of 12" and compressed is closer to 8.5". Using dual struts on a Husky tool box the 10 lb. pressure shocks…

view full answer...

Answer 2

If your existing hubs have a 5 on 4-1/2 inch bolt pattern the Dexter Trailer Hub and Drum Assembly #84546UC3 will work perfectly. This hub uses the #L68149 inner bearing and #L44649 outer bearing, is designed for 3,500 pound axles, and the bearings,…

view full answer...

Answer 3

I attached a picture that has all of the dimensions of the Reese Goose Box part #RP85FR that you asked about.

view full answer...

Answer 4

It really depends on state regulations. Some states don't require brakes on a trailer that weighs under 3,000 lbs, where other states may require them on any trailer with tandem axles or beyond a certain length. It may be accurate that it is so…

view full answer...

Answer 5

Hey Robbie, the Furrion Chill Cube RV Air Conditioner w Air Distribution Box #FR39TD that you referenced comes with everything needed to replace your Coleman Mach setup. How did you like your Coleman Mach Air?

view full answer...

Answer 6

Really the only way to tell if you have manual or self-adjusting brakes is to remove the hub and take a look inside. If you can see a cable running at an angle (see included photo), then you have self adjusting brakes like the Electric Trailer Brake…

view full answer...

Answer 7

It sounds like you're asking about the torque spec for the castle nut on your 3,500 lb axle. There is no specific torque rating when installing the castle nut on any axle. You want to run the nut down until there is no side to side play in the…

view full answer...

Answer 8

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 9

The Lippert 126003 is a 3,500 pound hub/drum and has a bolt pattern on 5 on 4-1/2 inches. The Trailer Hub and Drum Assembly #AKHD-545-35-K will be the replacement you will need. The hub and drum has an Inner Bearing #L68149 and an Outer Bearing…

view full answer...

Answer 10

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

Wheel bolt patterns are defined by two numbers: the first being the number of lug nuts and the second being the diameter of the circle the lug nuts are arranged in. So a 5 on 4-1/2 bolt pattern is 5 lugs arranged in a circle that is 4-1/2 inches in…

view full answer...

Replacement Hub for a Lippert LCI 126003 Hub

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching