How to Pick Out Trailer Hub Replacement for 1986 Shorelandr

Question

Question:

How can I find out what hub assembly I would need to entirely replace the both sides of my 1986 shore Landr boat trailer. what came off the one side...... LM67048 and LM11949 numbers a little hard to read I have pictures. Bearing buddy 1781

asked by: Ken C

0

Expert Reply:

Based on the bearings you have currently the only hub we offer that would fit as a replacement is the part # AH15450ECOMP which has a 4 on 5 inch bolt pattern.

I attached a help article on determining bolt pattern so that you can verify you have the same.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The D in 205/75D15 represents that the tire has a bias ply construction whereas the R in 205/75R15 represents that the tire has a radial ply construction. The difference between a bias and radial ply is in regard to the directions of the cords. In…

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

First, I would say if there is any question on the road worthiness of the trailer, take the steps to correct it. Better safe than sorry. Some trailers have wheels that are hub-centric, the wheel is centered on the hub using the center pilot holes.…

view full answer...

Answer 4

Thank you for the photo of your vintage utility trailer's spindle. The simplest and surest way to identify a compatible trailer hub is to identify the inner and outer bearings and the grease seal it uses. Matching up those components along with…

view full answer...

Answer 5

Yes, you can replace a square axle with a round beam axle so long as it is rated appropriately. You will need a new u-bolt kit for the round 2K axle, part #APUBR-10. We offer beam axles rated up to 3500-lbs and also axle-less suspension kits from…

view full answer...

Answer 6

The angled portion of the flanges on the part #115983 should run front to back on your trailer and should angle away from your leaf spring. See the attached picture to see exactly how they should install. Typically there are bushings installed in the…

view full answer...

Answer 7

You may be able to replace your existing axle that has an 84 inch hub face length with one that has an 89 inch hub face length without a problem but it's going to be dependent on your existing spring center length. This is the distance from the…

view full answer...

Answer 8

The LMX Red Grease like part #L11390 is the best overall grease for boat trailer applications like you mentioned. It's just as waterproof as any marine grease but is also more heavy duty so it's the way to go for sure.

view full answer...

Answer 9

You very well could use wheel studs instead of bolts by installing screw-in studs like the 1/2" x 2" Redline #25-53 or #25-51, or the 9/16" x 3" Redline #25-11. Just be sure that the stud is the correct size, the middle opening on…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

How to Pick Out Trailer Hub Replacement for 1986 Shorelandr

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching