Exploded Diagram of Draw Tite 15k Fifth Wheel Hitch

Question

Question:

I bought a drawtite 15000 pro series hitch from someone who didnt have installation diagram and im looking for something to help me install it. Was hoping to find a web site I could download from. Thanks

asked by: Donnie B

0

Expert Reply:

The hitch you have is MOST likely the previous generation of the part # RP30047 hitch. It's not the greatest quality, but I was able to find an exploded diagram of the hitch that I attached for you to check out.

I also attached a link to the install instructions as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

While we do not carry a direct replacement for your Covenant W914-36FT, the closest I was able to find the: -Greystone 32" Electric Fireplace with Crystals - Recessed Mount #324-000081. Based off of my research, your Covenant heater measures 36”…

view full answer...

Answer 2

For your B&W Companion Slider Gooseneck-to-5th-Wheel Trailer Hitch Adapter - Dual Jaw - 20,000 lbs #BWRVK3400 that draw down bolt is 1/2" x 3-1/2". We don't have the factory bolt and washer replacement, but you can use a grade 5…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hello John, thanks for reaching out. Since your bed is shorter that 8' we do recommend using a sliding 5th wheel hitch for extra clearance on tight turns. So for your 2020 Chevy 2500 I recommend the following: - B&W Patriot 5th Wheel Trailer…

view full answer...

Answer 8

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 9

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 10

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 11

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 12

Hey Heath, thanks for reaching out! The Curt A20 #C55DR and the B&W Companion #BWRVK3670 you're looking at are both excellent 5th wheel hitches, but I have to go with the Companion in this case simple because it is more robust and has a…

view full answer...

Exploded Diagram of Draw Tite 15k Fifth Wheel Hitch

Featured Help Information

Miscellaneous Media

Continue Researching