Motorcycle Wheel Chock in Toy Hauler Recommendation Where Under Trailer Access is Limited

Question

Question:

I just purchased an RV Outabck Terrian 230RS that has a Toy Hauler in the front side entry. The bottom of the trailer is covered so I can not access the bottom of the trainer to mount a Wheel Chock with bolts. I am looking for ideas on how I can mount a wheel chock under without access to the underside of the RV. It would also be great if the chock was removable. Thanks for your help.

asked by: Dan M

1

Helpful Expert Reply:

You could use the Tow-Rax Removable Wheel Chock # TWSPWC. You would not need to access the bottom of your trailer to install the install hardware. All you would need to do is drill hole for the anchors of the wheel chock and then you would be able to use the install bolts that thread into the anchors to secure the # TWSPWC.

I attached a review video for this product for you to check out as well.

expert reply by: Jameson C

1

Answer 1

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 2

Hey Rodney, For a rubber roof you can use the Alpha Systems 1021 Self-Leveling Sealant for RVs #AL98KV. This is self-leveling sealant so it's design to pool a bit before drying and would only be good for use on the roof. If you're needing any…

view full answer...

Answer 3

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

I think I have a solution for you in the Global Link RV Entry Door Locking Latch Kit, #295-000021 for white or, #295-000019 for black. This latch kit measures 3.47" wide x 4.28" tall, fits doors that are 1-1/4" to 1-1/2" thick,…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 8

The 235/80R16 size tire, like the Karrier ST235/80R16 Radial Trailer Tire #AM34903, will measure about 30.8" for overall diameter and have a section width of 9.25". This tire/wheel combo has an 8 on 6-1/2" bolt pattern. If you need a…

view full answer...

Answer 9

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 10

I can help you with greasing up your EZ Lube Axle. First thing I would check would be that the grease is not coming out of the back of the axle through the seal. If this is the case you will need to replace the seal. Our tubes like #L11390 have 14…

view full answer...

Motorcycle Wheel Chock in Toy Hauler Recommendation Where Under Trailer Access is Limited

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching