Replacement Electric Trailer Brakes for 1998 Coleman Fleetwood Sunridge Pop-Up Camper

Question

Question:

Hello, I just purchased a 1998 Coleman Fleetwood Sunridge pop up camper. I need to replace both electronic brakes. I have searched the web looking for a part number but havent found one yet. The ppl at advanced auto or the local RV place are no help either. These look like the same exact brakes that are on there now but i dont know for sure. can you help me? If these are the right ones do you carry both left and right side? Thanks

asked by: Bryan G

0

Expert Reply:

We can help you with new electric drum brakes for your Coleman pop-up!

You will just want to confirm a few details in order to select suitable replacement brake assemblies.

First, check the axle's weight rating. This should be on a plate or sticker on the axle itself. Note you need to select a matching set of left- and right-hand brakes. You also need to make sure you choose the same size brake as what is now on the trailer, both in diameter and width, and the same mounting bolt pattern. Once you know the weight capacity you can use the link provided to see all electric brake assemblies suitable for that requirement. You can use the filters on the page to narrow the displayed results based on your axle rating.

Let's say your axle is rated for 3500-lbs. This will be a 10 x 2-1/4-inch brake assembly. We offer etrailer.com Self Adjust brakes # AKEBRK-35L-SA (left) and # AKEBRK-35R-SA (right) and standard manual-adjust brakes # AKEBRK-35L and # AKEBRK-35R.

I have linked a video showing brake installation for your reference.

expert reply by: Adam R

0

Answer 1

I can absolutely understand not wanting to take your hub apart to find the right replacement hub, but unfortunately that is the only option as the numbers you referenced are not any type of indicator of a replacement. So, to determine the correct hub…

view full answer...

Answer 2

The 1998 Jayco Eagle 260FS weighs around 5,000 lbs so it is likely to have either 2,000-2,200 lb or 3,500 lb axles. If it uses 2,000-2,200 lb axles then you'll need the Bearing Kit part #BK1-100 but if it uses 3,500 lb axles then you'll need…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Based on what information I could find about AL-KO 8490 hub and drums, it is rated for 3,500 pound axles, has a 5 on 4-1/2 bolt pattern, and is a 10 by 2-1/4 inch drum. If this is the case, we have several options for you. I have attached a link to…

view full answer...

Answer 8

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Replacement Electric Trailer Brakes for 1998 Coleman Fleetwood Sunridge Pop-Up Camper

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching