view cartView Cart

CALL NOW - 800-298-8924

Product Experts Available Now!

Jeep Cherokee Trailer Wiring

change vehicle

Select Jeep Cherokee Year

Trailer Wiring

Custom fit Trailer Wiring for your:

Available Years for Trailer Wiring

Jeep Cherokee Trailer Wiring Harness

Make installing a trailer wiring harness on your Jeep Cherokee as easy as possible with a custom fit wiring harness from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, or Hopkins. A custom kit will eliminate or reduce the need to cut and splice wires in your Jeep Cherokee while helping to protect sensitive electronics.

What our customers are saying:

Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.


Mankato, MN

Wiring Adapter Fitguide

   Trailer Connectors and Adapters

   Wire and Wiring Accessories

Trailer Wiring Manufacturers

Jeep Cherokee Custom Fit Vehicle Wiring Videos

Trailer Wiring Harness Installation - 1999 Jeep Cherokee

Today, on our 1999 Jeep Cherokee, we'll be installing the tow-ready T-1 connector, part number 118354. We'll go ahead and show you how to use the new 4 pole connector. We'll simply take it, run it to the center of the vehicle and out, staying away from the latch as pinching the wire off in the latch can harm it. However, the weather stripping is thick enough that it won't, and we'll simply close the rear cargo door on the wire. Then, we can go ahead and pull out the new 4 pole wire as necessary to go down to the hitch or accessory. Then, once we're finished using our new 4 pole wire, we'll simply role it up and store it underneath the spare tire. To begin our install, we'll first open up the rear cargo door.

Trailer Wiring Harness Installation - 2014 Jeep Cherokee

Today, on this 2014 Jeep Cherokee, were going to install part number C56208 from Curt. This is the Curt T-connector vehicle wiring harness with a four-pole flat. Were going to need to get access back on the taillights so were going to have to open the back hatch. Now, our next step is very important. Well go to underneath the hood and disconnect the battery. Those electronics in this vehicle are so sensitive but this is essential to do this part. Well loosen up the negative terminal and just pull it off.

Trailer Wiring Harness Installation - 1998 Jeep Cherokee

Today on our 1998 Jeep Cherokee we'll be installing the Tow Ready T-One Connector. Part number 118354. To install our new connector we'll first need to open up the rear cargo area. Then we'll remove the spare tire bracket. Then we'll remove the six screws securing the rear threshold, and the three screws securing the driver's side rear quarter panel. Next we'll identify the plug we'll be plugging inline with at the manufacturer's harness. This will be the white plug closest to the rear cargo door. Before I make my connection I'm going to go ahead and start routing my wire back in behind the interior trim panel. Now with my wire fed over to the connector, we'll simply press on the locking tab and disconnect the two manufacturer's connection points.

Trailer Wiring Harness Installation - 2001 Jeep Cherokee

Alright today in this 2001 Jeep Cherokee, we're going to install part number 118354, from Tow Ready. First thing we need to do is go ahead and open up the back hatch, and remove the spare tire. After the spare tire is removed, we'll go ahead and remove the threshold as well. Okay, now we also have to remove the spare tire stand as well. Then we ahead and start work on pulling back the interior panel. Alright, once we have the panel pulled out of the way, we can see a row of connectors. The connector that's closest to the end of the vehicle is the one we want to plug into. So we'll disconnect it, and the install the T connector. Then we'll go ahead and locate the factory ground wire, and we'll attach a white wire at the ring terminal to there. Once we clean off the location for our converter box, we'll go ahead and remove the adhesive backing an install it. Now I go ahead and reinstall the interior panel, and the components, as well as the spare tire components. With that, that finishes our install. Now go ahead and show you how to use the four pull harness, it's stored inside the vehicle until it needs to be used. Next we'll pull out a little bit of the harness, and shut the hatch on it. Then we'll pull out what we need to go to our trailer.

Trailer Wiring Harness Installation - 2014 Jeep Cherokee

Today on our 2014 Jeep Cherokee, well be installing the tow-ready T-One Vehicle Wiring Harness with four-pole connector part number 118605. Now, to begin our install, well first go ahead and open up the rear cargo door. Then, well remove the spare tire wheel cover. Then well remove the cargo hooks here at the threshold. To remove them, well have the first pop-up plastic cap and then remove the Torx bit screw underneath. Now with those removed, we can remove the rear threshold by gently prying up on the threshold and releasing the fasteners underneath. Well set the threshold aside. Next, well remove the plastic surround in the spare tire wheel.

Trailer Wiring Harness Installation - 2000 Jeep Cherokee

Today on its 2000 Jeep Cherokee Sport well be installing part number 118354 from Tow Ready. T-one Harness install inside the vehicle sort of back catch and get access to the Wire Harness. All right a wire harness is behind this panel right here. The normal is spare tire align this is the spare tire not here. So were going to remove the threshold so that way we can have room to remove panel here on the side.Our T-One connects on fit in between these two pieces. So, lets go ahead and disconnect them.

Trailer Wiring Harness Installation - 1997 Jeep Cherokee

Today on this 1997 Jeep Cherokee we are going to install part number 118354 from Tow Ready. This T connector fits inside the vehicle on the driver side behind the tail light so what we need to do is get inside the vehicle to remove the spare tire and some interior panels. Now remove the fasteners for the spare tire bracket. Next we will remove the threshold panel. Now we need to remove the fasteners for this panel here. You do not have to take the whole panel loose but just for clarity we took it off. This is the connector right here that we have to disconnect and put our T connector into. It helps to pull this out a little bit to make easier working room. Push down this tab right here and it comes right apart and the T connector plugs right in between. Take everything and tuck it back into place. 01:42

Jeep Cherokee Custom Fit Vehicle Wiring Questions and Answers

  • Trailer Wiring Recommendation for a 1999 Jeep Cherokee
  • All you need to install a 4-way trailer wiring harness on your 1999 Jeep Cherokee is the Curt Wiring Harness part # C55345. This custom-fit T-connector plugs into your Jeep Cherokee's wiring harness, which is located behind the driver's-side interior trim panel in your rear cargo area. Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
    view full answer...

  • Troubleshooting Curt # C56208 Wire Harness Installation on 2014 Jeep Cherokee Latitude
  • Thank you for your recent purchase from etrailer of a hitch and trailer wiring harness. I am glad the hitch install went well and I am sorry for the issue with the wiring harness. I appreciate you providing specifics about your harness installation. That really helps us a lot. Apart from the plug-in T-connector fittings that match up with the connectors at the Cherokee's taillight assemblies, the only wiring required, other than attaching the ground wire, is the routing and connection...
    view full answer...

  • Troubleshooting Utility Trailer Taillights Stop/Turn Signals Not Functioning
  • It sounds like the problem is the trailer's wiring. I know it may seem like it is working correctly since you powered it with a 12 volt battery and it appeared to work like it should, but what is most likely the problem is either from having a weak ground on your trailer wiring or the trailer lights are drawing more power than the trailer wiring is rated for. Ground problems normally show up when there is more draw on a system such as when you have the running lights on and then use...
    view full answer...

  • Wiring Harness Recommendation for 2014 Jeep Grand Cherokee
  • The T-One Vehicle Wiring Harness that you will need for your 2014 Jeep Grand Cherokee is part # 118605. This harness will allow you to quickly and easily install a 4-way trailer connector on your Cherokee. I have also included an installation video for you. The T-One Vehicle Wiring Harness, # 118425, that you mentioned was designed for the 2007-2013 Jeep Grand Cherokee.
    view full answer...

  • Installing Trailer Wiring Harness # 118330 on 1993 Cherokee so Connector is Outside Vehicle
  • The recommended installation of the # 118330 would have the trailer connector remain in the cargo area of the vehicle until needed. This has the benefit of keeping the connector protected from the weather and from damage. I have the trailer connector in my van set up this way, and in all honesty, it works great. When I need the connector, I run it out the back and shut the rear hatch on the wire. As long as the wire is kept away from the latch, the weatherstripping will provide plenty of...
    view full answer...

  • Parts Needed to Flat Tow a 2014 Jeep Cherokee Limited Behind a Motor Home
  • Trailer wiring harness # 118605 is strictly for towing a trailer with your 2014 Jeep Cherokee Limited and cannot be converted for use as a flat towing harness. But I do have a great recommendation for you. For flat towing you can use wiring kit # HM55999. It is designed for use when flat towing your Jeep. In addition to the wiring I am sure you already know that you also need a few other items. For starters, you will need base plates. For your 2014 Jeep Cherokee Limited you can use #...
    view full answer...

  • Trailer Wiring Harness for a 1998 Jeep Cherokee
  • If your 1998 Jeep does not already have a trailer connector then you will need to install a wiring harness in order to power the lights on the trailer. You can use harness # 118354. I have linked a video showing how it installs on a 1997 Cherokee. The process will be the same on your 1998. Once the harness is installed you will have a 4-Way flat trailer connector at the back of the Jeep.
    view full answer...

  • Trailer Wiring Harness for a 1998 Jeep Cherokee Sport 4.0L
  • Yes, you can use Tow Ready trailer wiring harness # 118354 on your 1998 Jeep Cherokee Sport. This particular harness fits all models of the Jeep Cherokee from 1997 through 2001 model years. Installation on your 1998 model will be most like the video for the 1997 which I have linked for you. I have also included a link to the installation instructions for you.
    view full answer...

  • After Installing Curt Trailer Wiring Harness Right Turn Signal Does Not Work on 2014 Jeep Cherokee
  • It does sound like there is a potential problem with the Curt wiring harness # C56208. First, make sure that the connector with the green wire is plugged in on the passenger side and the yellow wire connector is on the driver side. Also make sure that the white ground wire is attached to a clean and corrosion free bare metal surface. You can try moving the ground to a different location as well. Inspect the pins in the harnesses connectors for the passenger side. You are looking...
    view full answer...

  • Can T-One Wiring Harness Be Installed On 2000 Jeep Cherokee With Factory Harness Already Installed
  • You can install the Tow-Ready T-One Vehicle Wiring Harness, part # 118354 on your 2000 Jeep Cherokee and leave the factory wiring harness connected. The instructions that are included with the T-One harness state that you will locate the connections behind the tail lights on the driver's side by removing the spare tire and rear quarter panel trim. When installing you will want to test the installation with a circuit tester like part # 3808. I have attached a link to an installation...
    view full answer...

  • Adding Heavy Duty 4/7-Way Connector to a 2014 Jeep Cherokee Trailhawk with Light Duty Tow Package
  • The heavy duty towing package on the 2014 Jeep Cherokee Trailhawk looks to be the same as # HM40975-11998. You could use this set up and what you would do is cut off the 4-Way and splice in the wires to the harness included with # HM40975-11998. On the harness the red wire is left turn signal and brake lights. White is ground. Green is right turn signal and brake lights. Brown is running lights. The functions that will not be used are the blue wire for electric brakes, black for...
    view full answer...

  • Installation Instructions for the Draw Tite Wiring Harness # 119178KIT
  • Check out the link I attached that will take you to the installation instructions for the Tow Ready wiring harness # 119178KIT. I also attached a link to an install video that details this process as well. The vehicle may not be the same as your 1989 Jeep Cherokee, but the installation will be the same.
    view full answer...

  • Availability of Trailer Wiring Harness for 1992 Jeep Comanche
  • My Contact at Curt Manufacturing tells me that the # C55330 should be the correct trailer harness for your Comanche given that it is based on the Cherokee, but did not have enough specific information to be 100 percent certain. Your best bet would be to locate the connector that your existing harness plugs into, and compare it to the T portion of the # C55330 shown in the photo I have provided. If the connectors look alike, the C55330 should work fine for you. If not, using a universal...
    view full answer...

  • Tow Ready Trailer Wiring Harness for a 1992 Jeep Cherokee
  • For the 1992 Jeep Cherokee you can use trailer wiring harness # 118330. I have included a link to the installation instructions for you to view. The harness that you have referenced, # 118354, is deigned to fit the 1997 to 2001 Jeep Cherokee but will not fit a 1992.
    view full answer...

  • Does 1996 Jeep Cherokee with Factory Tow Package Need a Trailer Tail Light Converter # 118330
  • If the trailer connector you currently have is factory installed, you should be good to go. The signals going to that connector should already be converted, so you will not need # 118330, which would be needed if the vehicle was never equipped with a trailer connector. It sounds as if you have a 7-way trailer connector, like part # PK11893 that has 6 blade-type pins with a contact in the center. You can use a circuit tester like part # 40376 to test the connector to ensure it is functional....
    view full answer...

  • Trailer Lights Not Working on 2001 Jeep Cherokee With Tow Ready T-One Wiring Harness # 118354
  • On the Tow Ready T-One Wiring Harness, part # 118354, if you find some, but not all, lighting functions work properly you may have a ground problem. In this situation a weak ground is just strong enough to provide some lighting functions but not all. When the taillights and brake lights are used at the same time, it creates the maximum amp load of the lights on the trailer. If a ground problem exists, it will show at this point. The places to check grounds are the connector on the vehicle....
    view full answer...

Stay Connected

Subscribe to email newsletter


privacy - we don't send unsolicited email reviews

All images, layout and content copyright