Customers compare GS-2250DL to these similar products
Products Featured in this Video
Today we're going to show you a True Ride seal for trailer bearings, part number GS-2250DL. All right, now it has an inside dimension of 2.250 inches and an outside diameter of 3.376 inches. Now this seal is typically used in applications where you have a easy lube axle. You can also use it on normal axles as well. It has two seals to help keep out water and road grime. When you replace your seal,… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
If you are getting a constant 3.4 volts on the brake output circuit of your brake controller without the brake pedal pressed that's a malfunction of the brake controller. Curt controllers are known to be a bit more prone to internal bugs so…
view full answer...The 4-Leaf Double-Eye Spring for 5,000-lb Trailer Axles #e44SR you're referring to is made in the USA.
view full answer...Hey Kevin thanks for your question. There is not much downside to going with the 5,000 lb springs instead of the 3,500 lb. A higher rated spring may make the ride a bit more "chunky" at times, since the spring would not flex as…
view full answer...Attached is a photo showing the dimensions of the bolt holes for the Dexter Electric Trailer Brake Kit #23-105-106. The bottom holes are separated by 3" on center while the other bolt holes are separated by 2-1/8" on center. I have also…
view full answer...A 6,000 lb axle is usually going to be 3" in diameter. Therefore, for the u-bolts you can use part #APUBR-8 for 7" long or part #APUBR-9 for 7-1/4" long. You can measure your existing u-bolts or from the bottom of the axle to the top…
view full answer...Nope, heavy-duty shackle straps are either 2-1/4" or 3-1/8", so the closest heavy-duty shackle strap to 2-3/4" would be the the 3-1/8" long, 1/2" thick Dexter Heavy-Duty Shackle Link #DX55FR. This option will still work for…
view full answer...The Never Fail Bushings like part #TRBU11566 and the Bronze Bushings like part #D014-077-00 are designed for 1-3/4" wide double eye leaf springs. There is not a version of these which are an upgrade over the factory nylon bushings for 2"…
view full answer...The calibration process of the Curt Spectrum #C51170 should only happen after initial installation and should be run before you plug in the trailer to your tow vehicle. You should have seen the green lights on the knob light up in a clockwise motion…
view full answer...According to the instructions for the Curt Spectrum Trailer Brake Controller #C51170 there are 2 reasons why the lights should be flashing. The first is if it's flashing red and yellow which means the brake controller is overloaded or there is a…
view full answer...The only difference between a 4 leaf spring and a 5 leaf spring like the #e34SR is that the 4 leaf spring will use slightly thicker leaves and is 1/8 of an inch shorter. To get the best measurement of your existing springs, measure the center eye to…
view full answer...If the rear springs are seemingly the correct length you could use them as a length reference. You can verify that the front and rear springs were the same length you could measure the distance between the center and front hanger as well as rear to…
view full answer...We offer some Dexter axles that might be a good replacement. You'll need to measure the hub face to hub face and spring seat to spring seat dimension of your current axle to see if what we offer is compatible. I've provided a diagram showing…
view full answer...