Cargo Van Mats Specs:
Features:
...Cushions and protects your cargo and the floor of your van using a 3/4" thick, closed-cell foam polypropylene mat Looks and feels like soft carpet Helps to safeguard brea...
Tech Tip:
Mat is sized for models with the Wall System along side walls. If your van has bare walls with exposed ribs, mat only extends to the ribs and so there will be a small gap along the side walls between those ribs.
More Information >Cargo Van Mats Specs:
Features:
...Cushions and protects your cargo and the floor of your van using a 3/4" thick, closed-cell foam polypropylene mat Looks and feels like soft carpet Helps to safeguard brea...
Tech Tip:
Mat is sized for models with the Wall System along side walls. If your van has bare walls with exposed ribs, mat only extends to the ribs and so there will be a small gap along the side walls between those ribs.
More Information >Videos
for Cargo Van Mats
Help Articles
for Cargo Van Mats
Expert Answers
for Cargo Van Mats
Unfortunately we do not have a way to replace the keys without knowing the key number for the lock. If they happened to have written down the key number from the lock then we will be able to get you a replacement. The etrailer Trailer Hitch…
view full answer...Base plate kits are somewhat time consuming but they aren't too terribly long. I once asked our install guy that's been here forever how long to set aside for a base plate kit install and he said a "long…
view full answer...I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is…
view full answer...The custom fit VanRug made for your 2015 Sprinter 2500 with 144in wheelbase is VanRug Custom Floor Mat for Cargo Vans - Charcoal Gray - Carpet #VRMS06M. It is designed for the cargo Sprinter Van and extends from behind front seats to under cargo…
view full answer...Yes. The Hydraulic Trailer Brake Kit - Uni-Servo - Dacromet - 10" - Left/Right Hand Assemblies - 3.5K #AKUBRK-35-D are compatible with the Dexter Trailer Hub and Drum for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 -…
view full answer...According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and…
view full answer...I suggest the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75912. It is a no drilling required install and takes the shortest amount of time to install in relation to other hitches for this model. While you…
view full answer...For your 2021 Chevrolet Blazer you're going to need to start with a base plate kit. Since there aren't any Blue Ox base plates I'd recommend going with the Roadmaster Direct-Connect Base Plate Kit #RM-523204-5. These are just…
view full answer...There is a trailer hitch receiver that fits your 2024 Mercedes-Benz Sprinter 2500, made by Curt. The correct part number is the following: - Curt Trailer Hitch Receiver #C13388
view full answer...The part you are looking for is the Brass Connector for Titan Disc Brake Kit, #T4750300. This is the fitting that threads into the master cylinder that accepts the reverse lockout solenoid on your Titan actuator. I have attached a link to this part…
view full answer...For your Sprinter 2500, I recommend the Curt Trailer Hitch Receiver #13358 that will do a great job for your bike carrier and more should you decide to tow later. This hitch model is designed for either the 144" or 170" wheelbase…
view full answer...You need the Wheel Retaining Ring #33-52-1 for your 10K axles and wheels. This ring has the single tab and will allow you to use your current flat faced wheel with Coned Lug Nuts #6-109. The retaining ring will sit outside the the wheels(see…
view full answer...