Cargo Van Mats Specs:
Features:
Protect the floor of your vehicle and get a slip-resistant, heavy-duty thermoplastic work surface backed with a 1/2" thick cushion for your load. A durable VanTred cargo van mat is great for tough, commercial applications and frequent use.
Tech Tip:
Mat is sized for models with the Wall System along side walls. If your van has bare walls with exposed ribs, mat only extends to the ribs and so there will be a small gap along the side walls between those ribs.
More Information >Cargo Van Mats Specs:
Features:
Protect the floor of your vehicle and get a slip-resistant, heavy-duty thermoplastic work surface backed with a 1/2" thick cushion for your load. A durable VanTred cargo van mat is great for tough, commercial applications and frequent use.
Tech Tip:
Mat is sized for models with the Wall System along side walls. If your van has bare walls with exposed ribs, mat only extends to the ribs and so there will be a small gap along the side walls between those ribs.
More Information >Videos
for Cargo Van Mats
Help Articles
for Cargo Van Mats
Expert Answers
for Cargo Van Mats
Unfortunately we do not have a way to replace the keys without knowing the key number for the lock. If they happened to have written down the key number from the lock then we will be able to get you a replacement. The etrailer Trailer Hitch…
view full answer...Base plate kits are somewhat time consuming but they aren't too terribly long. I once asked our install guy that's been here…
view full answer...I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR…
view full answer...The custom fit VanRug made for your 2015 Sprinter 2500 with 144in wheelbase is VanRug Custom Floor Mat for Cargo Vans - Charcoal Gray - Carpet #VRMS06M. It is designed for the cargo Sprinter Van and extends from behind front seats to under cargo…
view full answer...Yes. The Hydraulic Trailer Brake Kit - Uni-Servo - Dacromet - 10" - Left/Right Hand Assemblies - 3.5K #AKUBRK-35-D are compatible with the Dexter Trailer Hub and Drum for 3,500-lb Axles -…
view full answer...According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and…
view full answer...There are 3 different VanTred fitments for your 2023 Ford Transit T250 depending on the type of wheelbase you have: - 130" Wheelbase #VTFT15M -…
view full answer...There is a trailer hitch receiver that fits your 2024 Mercedes-Benz Sprinter 2500, made by Curt. The correct part number is the following: - Curt Trailer Hitch Receiver #C13388
view full answer...For your 2021 Chevrolet Blazer you're going to need to start with a base plate kit. Since there aren't any Blue Ox base plates…
view full answer...For your Sprinter 2500, I recommend the Curt Trailer Hitch Receiver #13358 that will do a great job for your bike carrier and more should you decide to tow later. This hitch model is designed for either the…
view full answer...You need the Wheel Retaining Ring #33-52-1 for your 10K axles and wheels. This ring has the single tab and will allow you to use your current flat faced wheel with Coned Lug Nuts #6-109. The retaining ring will sit outside the the wheels(see…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...Filter Products (4)
Contact and Help
What our customers are saying:
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Kevin
Manchester, MD