2011 Mazda 3 Trailer Hitch
2011 Mazda 3 Trailer Wiring
2011 Mazda 3 Brake Controller
2011 Mazda 3 Base Plate for Tow Bar
2011 Mazda 3 Vehicle Tow Bar Brake System
2011 Mazda 3 Vehicle Tow Bar Wiring
2011 Mazda 3 Roof Rack
2011 Mazda 3 Trunk Bike Rack
2011 Mazda 3 Air Filter
2011 Mazda 3 Exhaust
2011 Mazda 3 Transmission Cooler
2011 Mazda 3 Performance Chip Tuners
2011 Mazda 3 Vehicle Lights
2011 Mazda 3 Tire Chains
2011 Mazda 3 Fluid Filters
2011 Mazda 3 Vehicle Engine Heaters
2011 Mazda 3 Radiator Fan
2011 Mazda 3 Cabin Air Filter
2011 Mazda 3 Lift Assist
2011 Mazda 3 Floor Mats
2011 Mazda 3 Vehicle Covers
2011 Mazda 3 Bug Shield
2011 Mazda 3 Vehicle Seat Covers
2011 Mazda 3 Replacement Mirrors
2011 Mazda 3 Windshield Wiper Blades
2011 Mazda 3 Windshield Covers
2011 Mazda 3 Vehicle Air Mattress
Videos
for Mazda 3 Owners
Help Articles
Expert Answers
There are trailer hitches that will fit the 2011 Mazdaspeed 3 hatchback, but the Draw-Tite #C11393 will not fit. Instead, you can use the Curt Trailer Hitch, #C11383. This hitch comes with a ball mount, hitch pin and clip. I have included a link to…
I will be happy to make some hitch recommendations for your 2011 Mazda 3 Sport hatchback. I recommend Draw-Tite trailer hitch #24843. The reason I recommend it over the Curt option is because with Curt you would have to use stabilization strap #18050…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
I have a solution for carrying 3 bikes with your 2016 Mazda 3 hatch back but the Class I hitch can't handle carrying more than 2 bikes due to the added weight and leverage of the third bike that stick out further. You'd instead need a 2 inch…
The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…
On both the Hidden Hitch 60258 (discontinued) and the Draw-Tite, #24843, the top of the receiver tube will be approximately 1 inch below the bottom of the rear fascia. The bottom of the receiver will then be another 1-3/4 inches below that. Measure…
When you test the 4-Way on the Curt T-Connector Wiring Harness, part #56016, at the rear of your vehicle, it should show now power on all 3 pins with the lights off. If you have the vehicle head lights on, you should have around 12 volts at the brown…
We offer ball mounts that fit 1-1/4 inch hitches that are compatible with 2 inch hitch balls. For example we have the #3593 which fits that hitch size and then for a 2 inch hitch ball we have the #19258.
The Curt T-Connector Vehicle Wiring Harness part #C56011 is indeed the correct wiring harness for your 2015 Honda Accord without LED tail lights. The issue you are describing sounds like a ground issue. Please make sure that the ground you are using…
While there are not instructions available for removing the Yakima BaseLine Towers Y00146 from your 2016 Honda Civic I would be happy to walk you through the removal process. This will require the tightening tool that was included with your BaseLine…
Hello Dale. Without the tool, you may be able to remove the towers with an appropriately sized allen wrench, however this can be tricky. For security reasons, Yakima designed their towers so that they are not easily removed without the tool provided.…
Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer which…
