Combined wiring system - brake and turn signals are sent along the same wire.
Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Quickly and easily install a 4-way trailer connector on your vehicle. This T-One typically plugs directly into the back of your factory-installed 7-way connector so you can retain the 7-way and also pull a trailer that has a 4-pole flat.
Installation Notes:
Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket (sold separately)
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Install this socket in your truck bed for fast, easy hookup of a 5th-wheel or gooseneck trailer. Built-in magnet creates tight connection with an EZ Connector trailer-end plug (sold separately). Face-to-face contacts mean no bent or broken terminals.
Installation Notes:
This wiring is intended to be used with the 319-S7-10 trailer side plug, which is sold separately.
If your trailer has conventional 7-way wiring, this wiring harness is made compatible with an EZConnect Adapter, which is sold separately.
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Upgrade the 7-way connection on your vehicle and trailer with this complete kit. Built-in magnets create tight connection. O-rings make a watertight seal. Face-to-face contacts mean no bent or broken terminals. Includes plug holder and dummy plug.
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Replace the existing 7-way on your vehicle with this socket. Built-in magnet creates tight connection with EZ Connector trailer-end plug (sold separately). Face-to-face contacts mean no bent or broken terminals. O-ring on lid makes a watertight seal.
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
This wiring is intended to be used with the 319-S7-07 trailer side plug, which is sold separately.
If your trailer has conventional 7-way wiring, this wiring harness is made compatible with an EZConnect Adapter, which is sold separately.
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Replace the existing 7-way on your vehicle with this socket. Built-in magnet creates tight connection with EZ Connector trailer-end plug (sold separately). Face-to-face contacts mean no bent or broken terminals.
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
This wiring is intended to be used with the 319-R7-07 trailer side plug, which is sold separately.
If your trailer has conventional 7-way wiring, this wiring harness is made compatible with an EZConnect Adapter, which is sold separately.
More Information >Videos
for Custom Fit Vehicle Wiring
Help Articles
for Custom Fit Vehicle Wiring
Expert Answers
for Custom Fit Vehicle Wiring
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I&…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly -…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…
view full answer...